Toshiba RAV-GM1101AT8JP-E Скачать руководство пользователя страница 50

Страница: 50 / 84

Operation of diagnostic function

Judgment and measures

Check

code

Cause of operation

Status of air

conditioner

Condition

P03

Discharge temp. error

Discharge temp. (TD) over

specified value was detected.

Stop

Displayed when

error is detected

1. Check refrigerating cycle (Gas leak).

2. Trouble of PMV (Pulse Motor Value).

3. Check discharge temp. sensor (TD).

P04

High pressure SW system error

Stop

Displayed when

error is detected

1. Check service valves are fully opened.

(Gas side, Liquid side)

2. Check of outdoor fan operation.

3. Check clogging of outdoor PMV (Pulse Motor Valve).

4. Check clogging of heat exchanger in indoor/outdoor

units.

5. Short-circuit status of suction/discharge air in

outdoor unit.

6. Check outdoor P.C.board error.

7. Check fan system error (Cause of air volume drop)

at Indoor side.

8. Check PMV (Pulse Motor Valve) opening status in

indoor unit.

P05

Power supply error

Power supply voltage error

Open phase of 3-phase 4-wire

power supply

Stop

Displayed when

error is detected

1. Check power supply voltage. (AC342 to 457V)

2. Check open phase of 3-phase 4-wire power supply.

P07

Heat sink overheat error

Heat sink temp. sensor detected

over specified temperature.

Stop

Displayed when

error is detected

1. Check screw tightening between P.C.board and

heat sink and check radiator grease.

2. Check heat sink blast path.

P15

Gas leak detection

Discharge temp. sensor (TD),

Suction temp. sensor (TS)

detected temperature over

specified temp.

Stop

Displayed when

error is detected

1. Check gas leak, recharge.

2. Check full open of service valve.

3. Check PMV (Pulse Motor Valve).

4. Check broken pipe.

5. Check discharge temp. sensor (TD), suction temp.

sensor (TS).

P20

High pressure protective

operation

During cooling operation,

outdoor temp. sensor (TE)

detected temperature over

specified temp.

Stop

Displayed when

error is detected

1. Check outdoor heat exchanger sensor (TE).

2. Check full open of service valve.

3. Check indoor / outdoor fan.

4. Check PMV (Pulse Motor Valve).

5. Check clogging and short circuit of indoor / outdoor

heat exchanger.

6. Overcharge of refrigerant. Recharge.

P22

Outdoor fan system error

Stop

Displayed when

error is detected

1. Check lock of fan motor.

2. Check power supply voltage. (AC342 to 457V)

3. Check screw tightening between P.C.board and

heat sink and check radiator grease.

4. Check heat sink blast path.

5. Check outdoor P.C.board.

P26

Short-circuit of compressor

drive element

Stop

Displayed when

error is detected

1. When performing operation while taking-off

compressor wire, P26 error occurs.

Check control P.C.board.

2. When performing operation while taking-off

compressor wire, an error does not occur.

Compressor rare short.

P29

Position detection circuit error

Stop

Displayed when

error is detected

1. Check outdoor P.C.board.

FILE NO.SVM-18044

-1

- 50 -

P19

4-Way valve system error

After heating operation

has started, indoor heat

exchangers temp is down.

Stop

Displayed when

error is detected

1. Check 4-Way valve.

2. Check PMV.

3. Check indoor heat exchanger (TC/TCJ)

4. Check indoor P.C. board.

Содержание RAV-GM1101AT8JP-E





















































































Результаты поиска

Содержание RAV-GM1101AT8JP-E

Отзывы:

Бренды по названию

Популярные бренды

Toshiba RAV-GM1101AT8JP-E, Руководство по обслуживанию

Результаты поиска

Содержание RAV-GM1101AT8JP-E

Отзывы:

Бренды по названию

Популярные бренды