Toshiba RAV-GM1101AT8JP-E Скачать руководство пользователя страница 49

Страница: 49 / 84

Error mode detected by outdoor unit

Operation of diagnostic function

Judgment and measures

Check

code

Cause of operation

Status of air

conditioner

Condition

F04

Disconnection, short of discharge

temp. sensor (TD)

Stop

Displayed when

error is detected

1. Check discharge temp. sensor (TD).

2. Check outdoor P.C.board.

F06

Disconnection, short of heat

exchanger temp. sensor (TE)

Stop

Displayed when

error is detected

1. Check temp. sensor (TE).

2. Check outdoor P.C.board.

F08

Disconnection, short of outside air

temp. sensor (TO)

Stop

Displayed when

error is detected

1. Check outside air temp. sensor (TO).

2. Check outdoor P.C.board.

F12

Disconnection, short of suction

temp. sensor (TS)

Stop

Displayed when

error is detected

1. Check suction temp. sensor (TS).

2. Check outdoor P.C.board.

F13

Disconnection, short of heat sink

temp. sensor (TH)

Stop

Displayed when

error is detected

1. Check outdoor P.C.board.

(MCC-1627 (Q200) is incorporated in TH sensor)

F15

Miss-mounting of outdoor temp.

sensor (TE, TS)

Stop

Displayed when

error is detected

1. Check temp. sensor (TE, TS).

2. Check outdoor P.C.board.

F31

Outdoor P.C. EEPROM error

Stop

Displayed when

error is detected

1. Check outdoor P.C.board.

L10

Unset jumper of service P.C.board

Stop

Displayed when

error is detected

1. Outdoor service P.C.board.

Check model type setting jumper wire.

L29

Communication error between

MCUs of outdoor unit,

Stop

Displayed when

error is detected

1. Check outdoor P.C.board.

2. Check connection between outdoor P.C.boards.

H01

Compressor break down

Although operation has started,

operation frequency decreases

and operation stops.

Stop

Displayed when

error is detected

1. Check power supply voltage. (AC342 to 457V)

2. Overload operation of refrigerating cycle.

H02

Compressor lock

Over-current detection after

compressor start-up

Stop

Displayed when

error is detected

1. Trouble of compressor (Lock, etc.) : Replace

compressor.

2. Wiring error of compressor (Open phase).

H03

Current detection circuit error

Stop

Displayed when

error is detected

1. Check outdoor P.C.board.

(AC current detection circuit)

H04

Case thermostat operation

Abnormal overheat of

compressor

Stop

Displayed when

error is detected

1. Check case thermostat and connector.

2. Check gas leak, recharge.

3. Check full open of service valve.

4. Check PMV (Pulse Motor Valve).

5. Check broken pipe.

F07

Disconnection, short of heat

exchanger temp. sensor (TL)

Stop

Displayed when

error is detected

1. Check temp. sensor (TL).

2. Check outdoor P.C.board.

FILE NO.SVM-18044

-1

- 49 -

Содержание RAV-GM1101AT8JP-E





















































































Результаты поиска

Содержание RAV-GM1101AT8JP-E

Отзывы:

Бренды по названию

Популярные бренды

Toshiba RAV-GM1101AT8JP-E, Руководство по обслуживанию

Результаты поиска

Содержание RAV-GM1101AT8JP-E

Отзывы:

Бренды по названию

Популярные бренды