Toshiba RAV-GM1101AT8JP-E Скачать руководство пользователя страница 51

Страница: 51 / 84

Contents Error Display

When fixations of the errors were overlapped, the latest error is displayed.

: ON

: OFF

: Rapid flash (5 times /sec.)

The LEDs are located at the top right of the P.C.

board of the outdoor unit as shown in the figure

the right.

FILE NO.SVM-18044

-1

- 51 -

ITEM

No.

LED

Display

D800

D801

D802

D803

D804

D805

Normal

Discharge temperature sensor (TD) error

Heat exchanger temperature sensor (TE) error

Heat exchanger temperature sensor (TL) error

Outside air temperature sensor (TO) error

Suction temperature sensor (TS) error

Heat sink temperature sensor (TH) error

Heat exchanger sensor (TE, TS) connecting error

EEPROM error

Compressor breakdown

Compressor lock

Current detection circuit error

Thermostat for compressor activated

Model data not set

MCU-MCU commumication error

Discharge temperature error

High pressure SW error

Power supply voltage error

Heat sink overheating error

Gas leak detected

4-way valve reverse error

High pressure release operation

Fan system error

Short-circuit of compressor drive element

Position detection circuit error

Compressor IPDU or other (not specially identifi ed)

Power supply error

Check code

[

d remote

controller]

F04

F06

F07

F08

F12

F13

F15

F31

H01

H02

H03

H04

L10

L29

P03

P04

P05

P07

P15

P19

P20

P22

P29

D800 D801 D802 D803 D804 D805

(Yellow) (Yellow) (Yellow) (Yellow) (Yellow) (Green)

Inspection window

through which to

check the LED

displays

Electric parts cover

(Yellow) (Yellow) (Yellow) (Yellow) (Yellow) (

Green

)

Содержание RAV-GM1101AT8JP-E





















































































Результаты поиска

Содержание RAV-GM1101AT8JP-E

Отзывы:

Похожие инструкции для RAV-GM1101AT8JP-E

Бренды по названию

Популярные бренды

Toshiba RAV-GM1101AT8JP-E, Руководство по обслуживанию

Результаты поиска

Содержание RAV-GM1101AT8JP-E

Отзывы:

Похожие инструкции для RAV-GM1101AT8JP-E

Бренды по названию

Популярные бренды