Toshiba RAS-25J2AVSG-ND Скачать руководство пользователя страница 57

Страница: 57 / 123

Hi-POWER OPERATI

To automatically control room temperature and airflow for faster cooling or heating
operation (except in DRY and FAN ONLY mode)
Press

Press : Start and stop the operation

ECO OPERATI

To automatically control room temperature to save energy (except in DRY and FAN ONLY mode)

Press

: Start and stop the operation.

Note:

Cooling operation; the set temperature will increase automatically 1 degree/

hour for 2 hours (maximum 2 degrees increase). For heating operation the
set temperature will decrease.

. COMFORT SLEEP OPERATION

For comfortable sleep, automatically control air flow and automatically turn OFF (Except in DRY mode.)

1. Press

: Select 1, 3, 5 or 9 hrs for OFF timer operation.

Note:

The cooling operation, the set temperature will increase automatically

1 degree/hour for 2 hours (maximum 2 degrees increase). For heating
operation, the set temperature will decrease.

2. Press

: to cancel the comfort sleep operation.

HADA CARE FLOW OPERATION

HADA CARE FLOW

Air f

ow upward to the ceiling, provide Indirect air f

ow to body and homogenize

room

temperature

HADA CARE FLOW operation

Press

For start and stop HADA CARE FLOW

Cancel

HADA CARE FLOW

Note

● During HADA CARE FLOW mode, FIX and SWING button cannot active

- 57 -

Содержание RAS-25J2AVSG-ND




























































































































Результаты поиска

Содержание RAS-25J2AVSG-ND

Отзывы:

Похожие инструкции для RAS-25J2AVSG-ND

Бренды по названию

Популярные бренды

Toshiba RAS-25J2AVSG-ND, Руководство по обслуживанию

Результаты поиска

Содержание RAS-25J2AVSG-ND

Отзывы:

Похожие инструкции для RAS-25J2AVSG-ND

Бренды по названию

Популярные бренды