Toshiba MMK-AP0073H страница 140 Скачать руководство пользователя

Страница: 140 / 152

140

2. Every pushing [Unit, Louver

UNIT LOUVER

] button, the indoor unit address in the group are displayed successively.

Specify the indoor unit No. to be replaced.

3. Using the set temperature

buttons, the CODE No. (DN) can be moved up and down one by one.

4. First change the CODE No. (DN) from

. (Setting of filter sign lighting time)

Make a note of the set data displayed in this time.

5. Next change the CODE No. (DN) using the set temperature

buttons.

Also make a note of the set data.

6. Repeat item 5. and made a note of the important set data as shown in the below table.

∗

))

are provided in the CODE No. (DN). On the way of operation, DN No. may skip.

7. After finishing making a note, push

TEST

button to return to the usual stop status.

(Approx. 1 minute is required to be able to use the remote controller.)

Minimum requirements for CODE No.

Capacity of the indoor unit is necessary to set
the revolutions of the fan.

2 Replacement of service P.C. board

1. Replace the P.C. board with a service P.C. board.

In this time, setting of jumper line (cut) or setting of DIP switch on the former P.C. board should be reflected
on the service P.C. board. Refer to the following table about DIP switch setting and drawing of P.C. board
parts layout.

2. It is necessary to set Indoor unit to be exchanged : Remote controller = 1 : 1

Based upon the system configuration, turn on power of the indoor unit with one of the following items.

1) Single (Individual) operation

Turn on power of the indoor units and proceed to

2) Group operation

A) In case that power of the exchanged indoor unit only can be turned on.

Turn on power of the exchanged indoor unit only and proceed to

B) In case that power of the indoor units cannot be turned on individually. (

CASE 1

)

a) Remove temporarily the group wire connected to the terminal blocks A and B of the exchanged

indoor unit.

b) After connecting the remote controller wire only to the removed terminal block, turn on power of

the indoor units and proceed to

* When the above methods cannot be used, follow at the

CASE 2

below.

Contents

Indoor unit capacity

Refrigerant line address

Indoor unit address

Group address

TEMP.

ON / OFF

SET

TIME

TEST

FILTER

RESET

SAVE

SWING/FIX

VENT

UNIT LOUVER

CODE No.

UNIT No.

R.C. No.

TIMER SET

MODE

FAN

SET DATA

SETTING

Содержание MMK-AP0073H

























































































































































Результаты поиска

Содержание MMK-AP0073H

Отзывы:

Похожие инструкции для MMK-AP0073H

Бренды по названию

Популярные бренды

Toshiba MMK-AP0073H, Руководство по обслуживанию

Результаты поиска

Содержание MMK-AP0073H

Отзывы:

Похожие инструкции для MMK-AP0073H

Бренды по названию

Популярные бренды