Toshiba ME00070B Скачать руководство пользователя страница 20

Страница: 20 / 32

PROGRAMMING

ME00070B

TMS7 SERIES

Current Imbalance Sensitivity

Range

: 1 – 10

1 = Highest sensitivity (lowest imbalance)

5 = Average sensitivity

10 = Lowest sensitivity (highest imbalance)

Default Setting

: 5

Description

: Sets the sensitivity of the current imbalance

protection.

Adjustment

: The factory setting is suitable for most applications

however the sensitivity can be adjusted to accommodate site
specific tolerances

Undercurrent Protection

Range

: 15% – 100% FLC

Default Setting

: 20% FLC

Description

: Sets the trip point for the TMS7 undercurrent

protection as a percentage of motor full load current.

Adjustment

: Set to a level below the motors normal working

range and above the motor’s magnetising (no load) current.
To disable the undercurrent protection make a setting less than

the magneti sing current of the motor, typically 25% - 35% of
rated Full Load Current.

CAUTION

NOTE:

Undercurrent protection is only operative during

‘run’.

Stall Protection

Range

: 80% – 550% FLC

Default Setting

: 400% FLC

Description

: Sets the trip point for the TMS7 stall protection as

a percentage of motor full load current.

Adjustment

: Set as required.

CAUTION

NOTE:

Stall protection is operative only during ‘run’.

10.

Soft Stop Mode

Range

: 0 – 1

0 = Standard soft stop
1 = Pump control

Default Setting

: 0 (Standard soft stop)

Description

: Sets the active soft stop mode.

Adjustment

: The standard soft stop mode automatically

monitors motor deceleration and will provide optimum control for
most applications. Pump control may however offer superior

performance in some applications and can be of particular
benefit in some pumping applications.

20.

Local/Remote Operation

Range

: 0 – 3

0 = TMS7 Local/Remote push button always enabled.

1 = TMS7 Local/Remote push button disabled while motor

running.

2 = Local control only. (TMS7 push buttons enabled, remote

inputs disabled)

3 = Remote control only. (TMS7 push buttons disabled, remote

inputs enabled)

Default Setting

: 0 (Local/Remote button enabled)

Description

: Enables and disables the local push buttons and

remote control inputs. Also determines when and if the

Local/Remote push button can be used to switch between local
and remote control.

Adjustment

: Set as required

21.

Relay Output A Functionality

Range

: 0 –11

0 = Tripped
1 = Overcurrent trip

2 = Undercurrent trip
3 = Motor thermistor trip

4 = Starter overtemperature trip
5 = Phase imbalance trip

6 = Electronic shearpin trip
7 = Low current alarm
8 = High current alarm

9 = Motor overload alarm
10 = Start/Run

11 = Main contactor.

Start signal

Output voltage

RELAY FUNCTIONS

Main contactor

Start/Run

Run

Pre-start Tests

Default Setting

: 11 (Main Contactor)

Description

: Assigns the functionality of programmable relay

output A.

Adjustment

: Set as required

22.

Relay Output B Functionality

Range

: 0 - 11

Default Setting

: 10 (Start/Run)

Description

: Assigns the functionality of programmable relay

output B.

Adjustment

: Refer Function 21

Relay Output A Functionality

for

adjustment detail.

23.

Relay Output C Functionality

Range

: 0 - 11

Default Setting

: 0 (Tripped)

Description

: Assigns the functionality of programmable relay

output C.

Содержание ME00070B

































Результаты поиска

Содержание ME00070B

Отзывы:

Похожие инструкции для ME00070B

Бренды по названию

Популярные бренды

Toshiba ME00070B, Руководство пользователя

Результаты поиска

Содержание ME00070B

Отзывы:

Похожие инструкции для ME00070B

Бренды по названию

Популярные бренды