18
En
g
lis
h
SETTING UP YOUR TV
There are 3 methods for Wireless Setup:
•
Easy Setup
- If the AP supports Wi-Fi Protected
Setup, this method can be used. Wi-Fi Protected
Setup is an industry standard designed to make
connection of wireless LAN equipment and
security setup easy. Wi-Fi Protected Setup will
automatically configure all wireless settings.
NOTE:
WEP or TKIP encryption may not be
able to configured by easy setup.
•
Assisted Setup
- follow step 12.
Input the Security Key only.
•
Manual Setup
, skip to step 13.
Input the all settings.
NOTE: EXIT
is available during settings.
k
In step 10, when you select
Easy Setup
;
Press
BbC c
to highlight
Next
and press
OK
.
The
Easy Setup
screen will appear.
Press
c
and
B
/
b
to select
PBC
(
Push Button
Configuration
) or
PIN
(
Personal Identification
Number
)
and press
OK
.
Press
b
to highlight
Start Scan
and press
OK
.
PBC
- Following the on-screen instructions, push
the appropriate button on your AP. When a window
reporting that the setup is complete appears, press
OK
.
PIN
- When the PIN code window appears, enter
the displayed PIN into your AP, and then press
OK
to continue the PIN Setup. When a message
displays to report that the setup is complete, press
OK
.
To cancel searching for the AP:
Press
BACK
while searching for the AP. A message will
appear, and then press
C
/
c
to select
Yes
and press
OK
.
l
In step 10, when you select
Assisted Setup
;
Press
BbC c
to highlight
Next
and press
OK
.
The
Assisted Setup
screen will appear.
Press
B
/
b
to select the desired AP and press
OK
.
NOTE:
Check the MAC address on the label of the
AP or in the manual, and select your AP.
Press
B
/
b
to select
Security Key
and press
OK
.
The Software Keyboard window will appear (page
53).
Input the Security Key by using the Software
Keyboard. To save your setting, press the
GREEN
button.
NOTE:
• The Security Key must adhere to these
conditions:
- AES, AES/TKIP: 8-63 ASCII or 64 Hex
characters
- WEP: 5 or 13 ASCII or 10 or 26 Hex characters
• There is only one key ID to set for WEP
encryption.
Press
B
/
b
to highlight
Done
and press
OK
.
NOTE:
• If Network Name is not displayed, see Manual
Setup below to set Network Name before
Done
is selected.
• If
BACK
is pressed before
Done
is selected,
settings are not saved.
When the message “Wireless configuration is
complete.” appears on screen, press
OK
.
The screen will skip to step 14.
m
In step 10, when you select
Manual Setup
;
Press
BbC c
to highlight
Next
and press
OK
.
The
Manual Setup
screen will appear. Press
B
/
b
to select
Network Name
and press
OK
.
The Software Keyboard window will appear (page
53).
Input the Network Name by using the Software
Keyboard. To save your setting, press the
GREEN
button.
Press
B
/
b
to select
Authentication
and then
press
c
and
B
/
b
to select
Open System
,
Shared Key
,
WPA2/WPA-PSK (mixed mode
WPA2/WPA)
or
WPA2-PSK.
Press
OK
.
Press
B
/
b
to select
Encryption
, and then press
c
and
B
/
b
to select
None
,
WEP
,
AES/TKIP
or
AES
. Press
OK
.
NOTE:
• Certain encryption types are only compatible
with specific authentication types.
- When Authentication is
Open System
, only
WEP
or
None
is compatible.
- When Authentication is
Shared Key
, only
WEP
or
None
is compatible.
- When Authentication is
WPA2/WPA-PSK
(mixed mode WPA2/WPA)
, only
AES/TKIP
is
compatible.
- When Authentication is
WPA2-PSK
, only
AES
is compatible.
• When incompatible Authentication/Encryption
pairings are detected, a warning message will be
displayed, and no connection attempt will be
made until the incompatibility is resolved.
• There is only one key ID to set for WEP
encryption.
Press
B
/
b
to select
Security Key
and press
OK
.
Input the Security Key by using the Software
Keyboard (page 53).
