Toshiba e-STUDIO 55 Скачать руководство пользователя страница 159

Страница: 159 / 179

156

8. REPLACING STAPLES (OPTIONAL) (Cont.)

Set the staple cartridge.

Insert the cartridge until the claw catches it.

Note:

Repeat steps 1 to 11 if the test stapling
is not performed and "Set staple cartridge"
is displayed.

Reinstall the stapler unit in its previous

position.

Turn the blue lever 90 degrees to the right
to latch the stapler unit.

Confirm that the finisher is attached to the

copier, and that the paper size is set to any

size other than A5-R.

A staple test cannot be performed when only
the A5-R paper is available. So make sure to
set another size.

Close the front cover of the finisher.

Test stapling is automatically carried out

at some of 12 places of a blank sheet of

paper as in the right-hand figure.

No.12

No.3

No.2

No.1

Direction of
paper path

Staple
cartridge

Содержание e-STUDIO 55




















































































































































































Результаты поиска

Содержание e-STUDIO 55

Отзывы:

Toshiba e-STUDIO 55, Руководство оператора по функциям копирования, Страница: 159 / 179

Результаты поиска

Содержание e-STUDIO 55

Отзывы: