Toshiba e-studio 167 Скачать руководство пользователя страница 51

Страница: 51 / 220

Preparation 3 - Registering Size of Paper Placed 49

Press the [COPY] button several times until the lamp of the paper
size you placed in the drawer is lit.

If the [CANCEL] button is pressed at this step, the size is not registered and the
equipment will return to its normal status.

Press the [ENTER] button.

The paper size has been registered.

Registering other standard sizes

When standard size paper other than A3, A4, A4-R, A5-R or B4 is placed, register this size as
“OTHER” size.

In this section, LT size is registered in the drawer of the equipment as an example.

Press and hold the [COPY] and [DRAWER] buttons simultaneously
for more than two seconds.

The LCD screen shows as follows:

Select paper size

100%

NONSORT

ZOOM

FINISHING

EDIT

Содержание e-studio 167





























































































































































































































Результаты поиска

Содержание e-studio 167

Отзывы:

Toshiba e-studio 167, Руководство оператора по функциям копирования, Страница: 51 / 220

Результаты поиска

Содержание e-studio 167

Отзывы: