Toshiba e-studio 167 Скачать руководство пользователя страница 186 | Manualshive

Страница: 186 / 220

Toshiba e-studio 167 Скачать руководство пользователя страница 186

6 TROUBLESHOOTING

184 Replacing Toner Cartridge

Recommended toner cartridges

To assure an optimal printing performance, we recommend that you use TOSHIBA toner cartridges.

If you use a TOSHIBA-recommended toner cartridge, you can utilize the following two check functions of
this equipment:

Cartridge detecting function:

This function checks if the toner cartridge is correctly installed and notifies

you if it is not.

Toner-remaining check function:

This function notifies you when there is little toner remaining in the

cartridge, as well as notifying it to your service representative automatically by the remote service.

Any copying or printing operation is available even if you are using a toner cartridge other than the one
we recommend. In that case, however, the equipment cannot detect whether the toner cartridge is
installed or not and therefore an error message “Toner not recognized” appears on the LCD screen, even
if the toner cartridge is correctly installed. You cannot utilize the toner remaining check function and the
remote service function notifying your service representative automatically either.
If you are using a toner cartridge other than the one we recommend and you feel annoyed by this mes-
sage, contact your service representative. Your service technician will cancel the cartridge detecting func-
tion set by default. Remember once this function has been cancelled, you will not be able to utilize the two
functions mentioned above even if you change the cartridge to the one we recommend.

«
...
184
185
186
187
188
...
»

Содержание e-studio 167





























































































































































































































Отзывы:

Нет отзывов