Toshiba e-studio 167 Скачать руководство пользователя страница 148 | Manualshive

Страница: 148 / 220

Toshiba e-studio 167 Скачать руководство пользователя страница 148

5 CHANGING EQUIPMENT’S SETTINGS

146 Department Code

Deleting department codes

This section describes how to delete the department codes already registered. Key in the mas-
ter code in the department code entry screen, and then proceed to the following steps:

1

Press the [USER FUNCTIONS] button.

The “user functions mode” main screen is displayed.

2

Select “DEFAULT SETTINGS” with

and

buttons, and then

press the [ENTER] button.

3

Select “GENERAL SETTING” with

and

buttons, and then

press the [ENTER] button.

4

Select “DEPARTMENT CODE” with

and

buttons, and then

press the [ENTER] button.

USER FUNCTIONS

1216

01.DEFAULT SETTINGS

02.LISTS

03.INITIAL SETUP

DEFAULT SETTINGS

01.GENERAL SETTING

02.COPY SETUP

03.FAX SETUP

GENERAL SETTING
04.WEEKLY TIMER
05.SPEAKER VOLUME

06.DEPARTMENT CODE

«
...
146
147
148
149
150
...
»

Содержание e-studio 167





























































































































































































































Отзывы:

Нет отзывов