Toshiba DeviceNet DEV003Z-1 Скачать руководство пользователя страница 5

Страница: 5 / 45

E6581737

- 4 -

■

General Operation

Warning

Disassembly

prohibited

▼

Never disassemble, modify or repair.

Doing so could result in electric shock, fire and injury. For repairs, call your sales
agency.

Prohibited

▼

Do not attach this option to any inverter other than the VF-MB1/S15.

Doing so could result in electric shock or fire.

▼

When the inverter is energized, never detach the this option from the VF-MB1/S15.

Doing so could result in electric shock.

▼

Don't place or insert any kind of object into the DEV003Z (electrical wire cuttings, rods,

wires).
Doing so could result in electric shock or fire.

▼

Do not allow water or any other fluid to come in contact with the DEV003Z.

Doing so could result in electric shock or fire.

Mandatory

▼

Turn off the VF-MB1/S15 when installing and wiring this option.

▼

If the inverter begins to emit smoke or an unusual odor, or unusual sounds, immediately

turn power off.
If the equipment is continued in operation in such a state, the result may be fire. Call
your local sales agency for repairs.

■

Transportation & installation

Warning

Prohibited

▼

Do not operate the inverter if it is damaged or any component is missing.

Doing so could result in electric shock or fire. Call your local sales agency for repairs.

▼

Do not place any inflammable substances near the VF-MB1/S15 Inverter.

If an accident occurs in which flame is emitted, this could lead to fire.

▼

Do not install in any location where the inverter could come into contact with water or

other fluids.
Doing so could result in electric shock or fire.

Mandatory

▼

Operate under the environmental conditions prescribed in the instruction manual.

Operations under any other conditions may result in malfunction.

■

Wiring

Warning

Mandatory

▼

Shut off power when installing and wiring this option.

Wait at least 15 minutes and check to make sure that the charge lamp (VF-MB1/S15) is
no longer lit.

▼

Electrical construction work must be done by a qualified expert.

Installation or connection of input power by someone who does not have that expert
knowledge may result in fire or electric shock.

Содержание DeviceNet DEV003Z-1














































Результаты поиска

Содержание DeviceNet DEV003Z-1

Отзывы:

Похожие инструкции для DeviceNet DEV003Z-1

Бренды по названию

Популярные бренды

Toshiba DeviceNet DEV003Z-1, Руководство по эксплуатации функций

Результаты поиска

Содержание DeviceNet DEV003Z-1

Отзывы:

Похожие инструкции для DeviceNet DEV003Z-1

Бренды по названию

Популярные бренды