Toshiba D-R160SB, Руководство пользователя

Страница: 30 / 67

Basic Setup
30 EN
To select a channel
To skip a Preset channel
Move
Channel setting (cont’d)
7) Press [
K
/
L
] to start scanning.
• The tuner will begin to search up or down
automatically. When a channel is found, the unit
will stop searching and the picture will appear on
the TV screen.
• You can select a desired channel number using
[the Number buttons]. Refer to the following
Channel Plan table and press the three digits to
select the channel number.
(To select channel 4, press [0] first and then press
[0] and [4]. Or press [4] and then “– – 4” appears
and wait for 2 seconds.)
• If this is the channel you want, press [
s
].
Channel Plan
Ch. Indication TV Channel
01 - 10 IRA - IRJ, GAP
21 - 69 E21 - E69
74 - 78 X, Y, Z, Z+1, Z+2
80 - 99, 100 S1 - S20, GAP
121 - 141 S21 - S41
This unit can receive the Hyper and Oscar frequency
bands.
• If you want to decode scrambled signals, select
“Decoder” using [
K
/
L
], then press [
B
]. Select
“ON” using [
K
/
L
], then press [
s
].
• If “Skip” is set to “ON”, select “Skip” using [
K
/
L
],
then press [
B
]. Select “OFF” using [
K
/
L
], then
press [
s
].
• To store another channel, repeat steps 4 to 7.
8) After completion, press [SETUP] to exit.
Notes on using [the Number buttons]:
• Enter channel numbers as a two-digit number for
the quickest result. For example, to select channel
6, press [0] and [6]. If you only press [6], channel 6
will be selected after 2 seconds. You can only
select channels 1 to 99.
• You can select the external input mode “AV1”,
“AV2”, “AV3” or “AV4”.
• To select “AV1”, press [0], [0], [1].
• To select “AV2”, press [0], [0], [2].
• To select “AV3”, press [0], [0], [3].
• To select “AV4”, press [0], [0], [4].
You can set the unit to skip channels you can no longer
receive or seldom watch when you access channels
using [PROG. /
].
1) Follow steps 1 to 3 in “Manual tuning” on page
29.
2) Select “Position” using [
K
/
L
], then press [
B
].
3) Select the position number you wish to skip
using [the Number buttons] or [
K
/
L
], then
press [
s
].
4) Select “Skip” using [
K
/
L
], then press [
B
].
5) Select “ON” using [
K
/
L
], then press [
s
].
• To skip another channel, repeat steps 2 to 5.
6) Press [SETUP] to exit.
You can replace two channels.
1) In stop mode, press [SETUP].
2) Select “Channel” using [
K
/
L
], then press
[ENTER].
3) Select “Move” using [
K
/
L
], then press
[ENTER].
4) Select the position number you want to move
the channel using [
K
/
L
], then press [ENTER].
You cannot select a position number where “– – –”
appears next to the number, because “Skip” is set to
“ON” for that position number.
5) Move the channel to another position number
using [
K
/
L
], then press [ENTER].
• To move another channel, repeat steps 4 to 5.
6) Press [SETUP] to exit.
04̲Basic setup̲BD.indd 30 04̲Basic setup̲BD.indd 30 2006/02/24 18:02:41 2006/02/24 18:02:41