Toshiba Carrier RAS-09EACV-UL Скачать руководство пользователя страница 41

Страница: 41 / 111

Item

18. One-Touch

Operation flow and applicable data, etc.

Description

* Hi-POWER/

Fan
Operation

Time after operation
starts (min)

One touch comfort is the fully automated operation
that is set according to the preferable condition in
a region.

19. Hi-POWER

([Hi-POWER] button on the remote controller

is pressed)

When [Hi-POWER] button is pressed while the indoor
unit is in Auto or cooling operation, Hi-POWER mark

Comfort

*Hi-POWER/AUTO: Fan operates depends on the

setting temperature and room temperature.

During the One Touch Comfort mode if the indoor
unit receives any signal with other operation mode,
the unit will cancel the comfort mode and operates
according to the signal received.

When an indoor unit receives "One Touch
Comfort Signal" from the remote controller,

the indoor unit operates as following.

1) Air conditioner starts to operation when

the signal is received, even if the air

conditioner was OFF.

2) Target temperature is 22ºC [72°F].

3) Louver position is set as swing position.

4) Fan is controlled as followings.

Mode

is indicated on the display of the remote controller and
the unit operates as follows.

1. Automatic operation

•

The indoor unit operates in according to the

current operation.

2. Cooling operation

remote controller does not change.)
The indoor unit's fan speed level increase 1 tap

•

The preset temperature drops 1ºC [2°F]

(The value of the preset temperature on the

3. The Hi-POWER mode can not be set in Dry

operation

−

AUTO

Hi-POWER

AUTO

FILE NO. SVM-13071

Содержание Carrier RAS-09EACV-UL
















































































































Результаты поиска

Содержание Carrier RAS-09EACV-UL

Отзывы:

Бренды по названию

Популярные бренды

Toshiba Carrier RAS-09EACV-UL, Руководство по обслуживанию

Результаты поиска

Содержание Carrier RAS-09EACV-UL

Отзывы:

Бренды по названию

Популярные бренды