Toshiba Carrier RAS-09EACV-UL Скачать руководство пользователя страница 40

Страница: 40 / 111

Item

15. QUIET mode

Operation flow and applicable data, etc.

Description

When the [QUIET] button is pressed, the fan of the

indoor unit will be restricted the revolving speed at

−

until the [QUIET] button is pressed once

Remarks :

1. Quiet mode is unable to work in dry mode.

2. Quiet mode is appropriate to work with less

cooling load condition. Because of the fan

Quiet mode is the system which, control the
revolving speed of indoor fan to work
constantly at lower than speed L. In addition,
noise level of indoor unit is less than usual.

speed L

again (cancel Quiet mode).

speed L- may cause not enough the cooling

capacity or heating capacity.

16. COMFORT

The principles of comfort sleep mode are:

•

Quietness for more comfortable. When

•

Save energy by changing room temperature

•

The air condition can shut down by itself

Remarks:
1. Comfort sleep mode will not operate in dry

automatically.

mode and fan only mode.

automatically.

room temperature reach setting temperature

Cooling mode

•

The preset temperature will increase as

show on ECO operation (Item No. 9)

•

Press the [COMFORT SLEEP] button to
choose the operating hours. Repeat

pressing to select the hours.

•

If the [COMFORT SLEEP] button is pressed

again means cancel comfort sleep mode.

(1hr, 3hr, 5hr or 9hr)

−

SLEEP

FILE NO. SVM-13071

. FILTER

When the elapsed time reaches 1000 hours after

Indicator

conditioner operation, the FILTER indicator lights.
After cleaning the filters, turn off the FILTER indicator.

How to Turn Off FILTER Indicator

Press [RESET] button on the indoor unit.

NOTE :

If [RESET] button is pushed while the FILTER indicator
is not lit, the indoor unit will start the automatic
operation.

Содержание Carrier RAS-09EACV-UL
















































































































Результаты поиска

Содержание Carrier RAS-09EACV-UL

Отзывы:

Похожие инструкции для Carrier RAS-09EACV-UL

Бренды по названию

Популярные бренды

Toshiba Carrier RAS-09EACV-UL, Руководство по обслуживанию

Результаты поиска

Содержание Carrier RAS-09EACV-UL

Отзывы:

Похожие инструкции для Carrier RAS-09EACV-UL

Бренды по названию

Популярные бренды