Toshiba BU SERIES Скачать руководство пользователя страница 59

Страница: 59 / 94

58 / 92

http://www.toshiba-teli.co.jp/en/

D4253386C

● Setting

- Select the Input / Output

Set the following value to “LineModeAll” register. Setting value is Integer type.

Each bit corresponds to each Line (bit0=Line0, bit1=Line1).

Line2 is available. Line0 is dedicated input. Line1 is dedicated output.

LineModeAll

I/O connector pin assignment

0 (*)

Input

Output

* initial factory setting

- Select the Line of the I/O connector

Set the following value to “LineSelector” register. Select the line to output “LineSource” signal.

Setting value is Enumeration type.

LineSelector

I/O connector pin assignment

Line1 (*)

2 pin: GPIO Output

Line2

1 pin: GPIO Input / Output

* initial factory setting

- Select the source of GPIO output signal

Set the following value to “LineSource” register to change GPIO output signal selected by “LineSelector”.

Setting value is Enumeration type.

LineSource

Signal description

Off (*)

No output.

FrameTriggerWait

Indicating waiting a Random Trigger Shutter.

An External trigger is input during this period, exposure starts immediately.

FrameActive

Period from exposure start to CMOS transfer completion.

FrameTransfer

Period of transferring image data on USB bus.

ExposureActive

Period from exposure start to exposure end.

UserOutput

Outputs the value set in “UserOutputValueAll”.

Timer0Active

This signal can be used as strobe control signal.

The delay time and pulse width of this signal are configurable.

* initial factory setting

- Set the UserOutput signal

Set the following value to “UserOutputValueAll” register. Setting value is Integer type.

Each bit corresponds to each Line (bit0=Line0, bit1=Line1).

Содержание BU SERIES





























































































Результаты поиска

Содержание BU SERIES

Отзывы:

Похожие инструкции для BU SERIES

Бренды по названию

Популярные бренды

Toshiba BU SERIES, Инструкция по эксплуатации

Результаты поиска

Содержание BU SERIES

Отзывы:

Похожие инструкции для BU SERIES

Бренды по названию

Популярные бренды