TOSHIBA TEC Corporation B-FP Series Скачать руководство пользователя страница 14

Страница: 14 / 124

-8-

5.5.2

Icon

Five kinds of icon are displayed in the top line of the online mode display.
These icons are displayed in the online mode/error display.

Each mark are updated every 5 seconds.

Icon

Explanation

Wireless LAN icon

Displayed and used when the wireless LAN module is mounted.
The graph shows the strength of radio wave.

Graph 0: Outside the communication range

Graph 1: Strength of radio wave is weak.

Graph 2: Strength of radio wave is middle

Graph 3: Strength of radio wave is strong

Graph 4: Strength of radio wave is very strong

Bluetooth icon

Displayed and used when the wireless Bluetooth module is mounted.

OFF: Bluetooth connection invalid

ON: Bluetooth connection valid

Data transmission icon

Appears when a print job is present.

No connection

Data receiving

Data sending

Data receiving and sending

Battery level mark (*1)

Indicates a remaining battery power level (10 increments)

(Level1) Inoperative (low battery): (0%)

(Level2) Low (near-low battery): (10, 20%)

(Level3) Medium: (30, 40, 50, 60%)

(Level4) High: (70, 80%)

(Level5) Full (full charge): (90, 100%)

Charging

Error mark

Indicates a printer error status

OFF

Not in error state

In error state

Содержание B-FP Series





























































































































Результаты поиска

Содержание B-FP Series

Отзывы:

TOSHIBA TEC Corporation B-FP Series, Руководство пользователя, Страница: 14 / 124

Результаты поиска

Содержание B-FP Series

Отзывы: