TOSHIBA TEC Corporation B-FP Series Скачать руководство пользователя страница 123

Страница: 123 / 124

-117-

time to shift to power save mode, the printer enters power save mode.

11.2 When A Wireless LAN Module Is Connected

When a wireless LAN module is connected, “Power Save Mode Setting” inside the module is switched from “No
Power Save

” to “Auto Power Save” after the printer enters power save mode*.

*: Only when the wireless LAN power save setting is enabled.

11.3 Precausions

The printer does not enter power save mode under any of the following conditions.



When any error is displayed.



When the “BASIC interpreter” runs.



When the printer is in system mode.



When the printer pauses.



When the printer is setting mode

Hidden spec [Reproduction prohibited]

Special case that printer doesn’t go to power save mode internally.

1) USB connection
2) About B-FP3D-GH/GS30 model, stage of motor protect is other than 0(idle).

Содержание B-FP Series





























































































































Результаты поиска

Содержание B-FP Series

Отзывы:

TOSHIBA TEC Corporation B-FP Series, Руководство пользователя, Страница: 123 / 124

Результаты поиска

Содержание B-FP Series

Отзывы: