background image

2

Adding Fuel to the Machine

No Parts Required

Procedure

Add fuel to the machine before starting it. Refer
to your

Operator’s Manual

for the correct fuel and

procedure.

3

Checking the Engine-Oil
Level

No Parts Required

Procedure

Before you start the engine and use the machine,
check the oil level in the engine crankcase; refer to
the

Operator's Manual.

4

Checking the Tire Pressure

No Parts Required

Procedure

Air pressure specification: 90 kPa (13 psi)

Note:

Check the tire pressure before starting the

machine. Refer to your

Operator’s Manual

for the

correct tire type, correct air pressure needed, and
procedure.

5

Checking the Wheel Lug
Nut Torque

No Parts Required

Procedure

Before you start the engine and use the machine,
check the wheel lug nut torque; refer to Checking the
Wheel Lug Nuts in the

Operator's Manual

6

Checking the Grass
Deflector

No Parts Required

Procedure

If there are plastic ties holding the grass deflector up,
remove them and lower the deflector into place.

WARNING

An uncovered discharge opening could allow
the machine to throw objects in the operator's
or bystander's direction and result in serious
injury or death. Also, contact with the blade
could occur.

Never operate the lawn mower unless you
install a cover plate, a mulch plate, grass
deflector or bagger.

1.

Ensure that 1 end of the spring is installed
behind the deck edge before installing the bolt
as shown in

Figure 8

.

2.

Place the other end of the spring around the
grass deflector (

Figure 8

).

Important:

The grass deflector must be free

to rotate with downward tension. Lift the
deflector up to the fully open position and
ensure that it rotates freely, without binding
into the fully down position.

4

 

Содержание Z Master 3000 SERIES

















Отзывы: