Toro Z Master 3000 SERIES Скачать руководство пользователя страница 16

Dealer Initial

Customer Initial

Check Procedure

Z Stand® (if applicable)

Adjustable seat

Hydraulic-bypass valves

Rollover Protection System (ROPS)

Deck-flow baffle

Refer to the

Operator's Manual

to point out safety procedures, operation, and

maintenance procedures.

Review the warranty statement as shown in the

Operator's Manual.

Describe the post sale service procedures for your store.

Assist the customer in filling out and mailing the registration card or register online at

www.Toro.com

Make sure that the customer receives the

Operator's Manual

,

Engine Owner's Manual

,

Set Up Instructions

, and operator training material.

Make sure the customer knows the

Parts Catalog

is available at

www.Toro.com

.

Assist the customer in loading the machine.

Note:

When you, the dealer representative, have finished delivering the machine to the customer, sign and

date in the space provide below and keep a copy of this page for dealer records. Also, the dealer must remind
the customer to use a full-width trailer ramp to load the machine.

Signature:

Date:

Signature:

Date:

16

 

Содержание Z Master 3000 SERIES

















Отзывы: