Toro WorkmanR e2050 Скачать руководство пользователя страница 66

Страница: 66 / 120

Workman e2050/e2065

Transaxle and Brakes (Rev. B)

Page 4 – 6

Adjustments

Adjust Brakes (Workman e2050)

The recommended brake pedal travel is from 1” to 1 1/2”

(25.4 to 38.1 mm) with a 75 to 100 pound (34 to 45.4 kg)

input force to the brake pedal.

Adjustment Procedure (Figures 1 and 2)

1. Park vehicle on a level surface, turn on/off switch

OFF and remove key from the on/off switch.

2. Depress brake pedal lightly (10 to 15 pound input

force) until resistance is achieved. Check the gap be-

tween the brake lever and the brake lever stop to deter-

mine the distance the brake equalizer needs to be

adjusted (Fig 2).

3. Remove the cotter pin and clevis pin that secure the

brake rod clevis to the brake lever.

4. Disconnect the spring from the hole near the end of

the brake rod.

5. Press the brake pedal down fully to raise the brake

lever away from the brake rod clevis.

6. Thread the brake rod in or out of the brake equalizer

as needed to remove the gap identified in Step 2. Do not

overtighten or brakes will drag and wear prematurely.

7. Reinstall the spring into the hole in the brake rod.

NOTE:

Use a pry bar placed between the accelerator

pivot shaft and the brake equalizer to aid in installation

of the clevis pin that secures the brake rod clevis to the

brake lever.

8. Connect the brake rod clevis to the brake lever using

the clevis pin and cotter pin removed previously.

9. Verify that brake pedal travel is from 1” to 1 1/2” (25.4

to 38.1 mm) with a 75 to 100 pound (34 to 45.4 kg) input

force to the brake pedal.

1. Clevis pin/cotter pin

2. Brake

lever

3. Brake rod clevis

4. Brake

rod

5. Brake

equalizer

6. Spring

7. Brake

cable

8. Accelerator pedal shaft

Figure 1

1. Brake

lever

2. Brake lever stop

3. Clevis pin/cotter pin

4. Brake rod clevis

5. Brake

equalizer

Figure 2

Содержание WorkmanR e2050

























































































































Результаты поиска

Содержание WorkmanR e2050

Отзывы:

Похожие инструкции для WorkmanR e2050

Бренды по названию

Популярные бренды

Toro WorkmanR e2050, Руководство по обслуживанию

Результаты поиска

Содержание WorkmanR e2050

Отзывы:

Похожие инструкции для WorkmanR e2050

Бренды по названию

Популярные бренды