manualshive.com logo in svg

Toro WorkmanR e2050, Руководство по обслуживанию, Страница: 90 / 120

Поделиться
Скачать
Toro WorkmanR e2050 Скачать руководство пользователя страница 90

Workman e2050/e2065

Page 5 – 4

Chassis (Rev. B)

Suspension and Steering (continued)

ÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁ

Problem

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Possible Cause

ÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á ÁÁÁÁÁÁÁÁÁÁÁÁ

Á ÁÁÁÁÁÁÁÁÁÁÁÁ

Á ÁÁÁÁÁÁÁÁÁÁÁÁ

Á ÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁ

Steering is hard.

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Tire pressure is low or uneven between tires.

Front wheel alignment (toe–in) is incorrect.

Steering linkage is binding or damaged.

Steering gear is damaged or worn.

ÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á ÁÁÁÁÁÁÁÁÁÁÁÁ

Á ÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁ

Vehicle pulls to one side when not

braking.

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

Á ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Á

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Tire pressure is low or uneven between tires.

Front wheel alignment (toe–in) is incorrect.

Steering or suspension component may be bent.

Содержание WorkmanR e2050

























































































































Отзывы:

Нет отзывов