Toro TITAN ZX6050 Скачать руководство пользователя страница 52

Страница: 52 / 56

Problem

Possible Cause

Corrective Action

1. By pass valves is not closed tight.

1. Tighten the by pass valves.

2. Pump belt is worn, loose or broken.

2. Change the belt.

3. Pump belt is off a pulley.

3. Change the belt.

4. Broken or missing idler spring.

4. Replace the spring.

Machine does not drive.

5. Hydraulic oil level is low or too hot.

5. Add hydraulic oil to reservoirs or let it

cool down.

1. Cutting blade(s) is/are bent or

unbalanced.

1. Install new cutting blade(s).

2. Blade mounting bolt is loose.

2. Tighten the blade mounting bolt.

3. Engine mounting bolts are loose.

3. Tighten the engine mounting bolts.

4. Loose engine pulley, idler pulley, or

blade pulley.

4. Tighten the appropriate pulley.

5. Engine pulley is damaged.

5. Contact an Authorized Service Dealer.

6. Blade spindle is bent.

6. Contact an Authorized Service Dealer.

Abnormal vibration.

7. Motor mount is loose or worn.

7. Contact an Authorized Service Dealer.

1. Blade(s) not sharp.

1. Sharpen the blade(s).

2. Cutting blade(s) is/are bent.

2. Install new cutting blade(s).

3. Mower deck is not level.

3. Level mower deck from side-to-side

and front-to-rear.

4. Underside of mower is dirty.

4. Clean the underside of the mower.

5. Tire pressure is not correct.

5. Adjust the tire pressure.

Uneven cutting height.

6. Blade spindle bent.

6. Contact an Authorized Service Dealer.

1. Mower deck belt is worn, loose or

broken.

1. Install new deck belt.

2. Mower deck belt is off pulley.

2. Install mower deck pulley and check

the idler pulley, idler arm and spring for
correct position and function.

3. Pump drive belt is worn, loose or

broken.

3. Check the belt tension or install new

belt.

Blades do not rotate.

4. Broken or missing idler spring.

4. Replace the spring.

Содержание TITAN ZX6050

























































Результаты поиска

Содержание TITAN ZX6050

Отзывы:

Похожие инструкции для TITAN ZX6050

Бренды по названию

Популярные бренды

Toro TITAN ZX6050, Руководство оператора

Результаты поиска

Содержание TITAN ZX6050

Отзывы:

Похожие инструкции для TITAN ZX6050

Бренды по названию

Популярные бренды