manualshive.com logo in svg

Toro TITAN ZX6050, Руководство оператора, Страница: 9 / 56

Поделиться
Скачать
Toro TITAN ZX6050 Скачать руководство пользователя страница 9

110-6691

1.

Thrown object hazard—keep bystanders a safe distance
from the machine.

2.

Thrown object hazard, mower—do not operate the without
deflector, discharge cover or grass collection system in
place.

3.

Cutting/dismemberment of hand or foot—stay away from
moving parts.

112-9840

1.

Read the

Operator’s

Manual

.

3.

Remove the ignition key
and read the instructions
before servicing or
performing maintenance.

2.

Height of cut

117-1194

1.

Engine

115-9644

1.

Press the pedal and lift the height of cut lever to unlock
the deck position.

2.

Height of cut

3.

Press the pedal to move the deck to the transport position

Battery Symbols

Some or all of these symbols are on your battery

1.

Explosion hazard

6.

Keep bystandersa safe
distance from the battery.

2.

No fire, open flame, or
smoking.

7.

Wear eye protection;
explosive gases can
cause blindness and other
injuries

3.

Caustic liquid/chemical
burn hazard

8.

Battery acid can cause
blindness or severe burns.

4.

Wear eye protection

9.

Flush eyes immediately
with water and get medical
help fast.

5.

Read the

Operator’s

Manual.

10.

Contains lead; do not
discard.

9

Содержание TITAN ZX6050

























































Отзывы:

Нет отзывов