Toro TITAN ZX6050 Скачать руководство пользователя страница 8

Страница: 8 / 56

Safety and Instructional
Decals

Safety decals and instructions are easily visible to the operator and are located near any area of
potential danger. Replace any decal that is damaged or lost.

99-8936

Machine speed

Neutral

Fast

Reverse

Slow

115-9625

Parking
brake—disengaged

Parking brake—engaged

117-1158

Bypass lever position for
operating the machine

Bypass lever position for
pushing the machine

115-9632

Power take-off (PTO),
Blade control switch on
some models

Fast

Blade control switch—On

Continuous variable
setting

Blade control switch—Off

Slow

Choke

114-1606

Entanglement hazard, belt—keep all guards in place.

93-7009

Warning—don’t operate the mower with the deflector up or
removed; keep the deflector in place.

Cutting/dismemberment hazard of hand or foot, mower
blade—stay away from moving parts.

Manufacturer’s Mark

Indicates the blade is identified as a part from the original
machine manufacturer.

Содержание TITAN ZX6050

























































Результаты поиска

Содержание TITAN ZX6050

Отзывы:

Похожие инструкции для TITAN ZX6050

Бренды по названию

Популярные бренды

Toro TITAN ZX6050, Руководство оператора

Результаты поиска

Содержание TITAN ZX6050

Отзывы:

Похожие инструкции для TITAN ZX6050

Бренды по названию

Популярные бренды