Toro TITAN ZX6020 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 60

Toro TITAN ZX6020 Скачать руководство пользователя страница 39

Charging the Battery

WARNING

Charging the battery produces gasses that can
explode.

Never smoke near the battery, and keep sparks and
flames away from battery.

Important:

Always keep the battery fully charged. This

is especially important to prevent battery damage when
the temperature is below 32°F (0°C).

1.

Charge the battery for 10 to 15 minutes at 25 to 30
amps or 30 minutes at 10 amps.

2.

When the battery is fully charged, unplug the charger
from the electrical outlet, then disconnect the charger
leads from the battery posts (Figure 48).

3.

Install the battery in the machine and connect the
battery cables, refer to Installing the Battery.

Note:

Do not run the machine with the battery

disconnected; electrical damage may occur.

Figure 48

1.

Positive battery post

3.

Red (+) charger lead

2.

Negative battery post

4.

Black (-) charger lead

Servicing the Fuses

The electrical system is protected by fuses. It requires
no maintenance; however if a fuse blows, check the
component/circuit for a malfunction or short.

Note:

The fuses are located on right hand console next to

the seat (Figure 49).

Fuses:

•

Main, 30 amp, blade-type

•

Engine, 20 amp, blade-type

To replace a fuse, perform the following:

1.

Grasp the fuse and pull it straight and away from the
fuse block.

30

25

1

2

3

4

G020320

Figure 49

1.

30 amp

3.

Open accessory slot

2.

25 amp

4.

Fuse block

Important:

Ensure that the new fuse is the same

type and the amperage as the fuse removed in step
1.

2.

Align a new fuse with the slot in the fuse block
(Figure 49).

3.

Push the fuse into the fuse block until the fuse is seated
(Figure 49).

39

«
...
37
38
39
40
41
...
»

Содержание TITAN ZX6020





























































Отзывы:

Нет отзывов