manualshive.com logo in svg

Toro TITAN ZX6020, Руководство оператора, Страница: 31 / 60

Поделиться
Скачать
Toro TITAN ZX6020 Скачать руководство пользователя страница 31

Figure 33

Located on the seat pan underside

1.

Read the

Operator's Manual

before performing any

maintenance.

4.

Check the hydraulic oil every 25 hours

2.

Check the engine oil every 8 hours

5.

Check the caster wheel tire pressure every 25 hours

3.

Check the drive wheel tire pressure every 25 hours

6.

Lubricate the caster wheel every 25 hours

Premaintenance
Procedures

Raising the Seat

Make sure the motion control levers are locked in the neutral
lock position. Lift the seat forward.

The following components can be accessed by raising the seat:

•

Service decal

•

Fuses

•

Battery and cables

Lubrication

Greasing the Bearings

Service Interval:

Every 25 hours—Grease all lubrication

points.

Grease Type:

No. 2 General Purpose Lithium Base Grease

1.

Park the machine on a level surface and disengage the
blade control switch.

2.

Move the motion control levers outward to the neutral
lock position, stop the engine, remove the key, and
wait for all moving parts to stop before leaving the
operating position.

3.

Clean the grease fittings with a rag (Figure 33 and
Figure 34). Make sure to scrape any paint off of the
front of the fitting(s).

31

Содержание TITAN ZX6020





























































Отзывы:

Нет отзывов