Toro Sand Pro 3020 Скачать руководство пользователя страница 20

Страница: 20 / 28

+)52'

12+/) #&,534+/) 1+/

'#2+/)

Raise one rear wheel off floor and place support

blocks under frame.

Start engine and set throttle to allow engine to run

at approximately 1800 rpm.

Actuate the lift valve lever until the lift cylinder rod

moves in and out several times. If cylinder rod does not

move after 10-15 seconds or pump emits abnormal

sounds, shut the engine off immediately and

determine cause or problem. Inspect for the following:

Loose filter or suction lines.

Loose or faulty coupler on pump.

Blocked suction line.

Faulty charge relief valve.

Faulty charge pump.

If cylinder moves in 10-15 seconds, proceed to

step 7.

04' *8&2034#4+% 42#/3.+33+0/ 3'26+%' .#/5#-

$5--'4+/ 0 #/& # 2'1#+2 .#/5#- $5--'4+/ 0

%#/ $' 0$4#+/'& (20.

5/&342#/& 02102#4+0/

#34 4* 42''4

.'3 07#

Operate the traction pedal in forward and reverse

directions. Wheel off floor should rotate in the proper

direction. If wheel rotates in wrong direction, stop

engine, remove lines from rear of pump and reverse

the locations. If wheel rotates in proper direction, stop

engine and adjust the spring adjusting pin lock nut.

Adjust traction neutral position: refer to Adjusting For

Neutral Position In Traction Drive, page 19.

Check adjustment of traction interlock switch:

refer to Adjusting Traction Interlock Switch.

Install engine shield and lower seat.

" ! !

Place the front wheel in the straight ahead position.

Adjust the locknuts until the chain is snug on both

sides of sprocket.

Turn the steering wheel full left and full right to be

sure the chain does not bind or hang up in either

direction. Readjust as required.

+)52'

&,534+/) /543

Since the chain and sprocket are subjected to sand

thrown up by the front tire, inspect them frequently for

wear. If either the chain or sprocket is worn beyond

acceptable limits, BOTH should be replaced.

" !

An in-line filter is incorporated into the fuel line.

Change filter every 800 hours. Use the following

procedures when replacement becomes necessary:

Close fuel shut-off valve.

Clamp both fuel lines that connect to the fuel filter

so gasoline cannot drain when lines are removed.

Loosen the hose clamps at both ends of the filter

and pull fuel lines off filter.

+)52'

5'- +-4'2

03' -#.13

Содержание Sand Pro 3020





























Результаты поиска

Содержание Sand Pro 3020

Отзывы:

Похожие инструкции для Sand Pro 3020

Бренды по названию

Популярные бренды

Toro Sand Pro 3020, Руководство оператора

Результаты поиска

Содержание Sand Pro 3020

Отзывы:

Похожие инструкции для Sand Pro 3020

Бренды по названию

Популярные бренды