background image

7

Specifications

Note:

 Specifications and design are subject to change without notice.

Machine Drive

Kohler, 4 cycle air cooled 22 H.P. engine @ 3600 rpm, 41.1 cu. in. (674 cc)

displacement. Oil capacity is 4 pints w/filter. Mechanical fuel pump. Gas tank

capacity is 4 gallons.

Frame

All welded structural rectangular 11 ga. tubing.

Hitch

Pin–type, 3/4” dia. vertically adjustable in 1” increments.

Fan

Centrifugal type–double inlet; 4 blade, 16” wide, 23–14” diameter, 3/16” thick, high

tensile steel. Shaft mounted in self–aligning, sealed ball bearings. Blower inlet area

is 286 sq. in., blower discharge area is 255 sq. in. Twin fan hood construction for

uniform air distribution: 4–1/2” deep x 63” wide (inlet area–283 sq. in.); variable

position from weighted rubber flap.

Fan Drive

Banded double drive belt direct from drive shaft to fan impeller drive shaft with

driver pulley, fan with driven pulley. Fan impeller runs at 1580 R.P.M. (tip speed

9100 ft./min.) at 3250 engine R.P.M.

Hopper

5–3/4 cu. yd. volume; 18 gauge top section with 16 gauge bottom section–rib

reinforced; full width self cleaning semi–automatic dumping.

Flex Tip Reel

Forward spinning with 6 rows of teeth. All steel construction with replaceable nylon

teeth; each row containing 11 individually spring–loaded flexible sets, 552 teeth

total; shaft set in self–aligning sealed bearings. Reel supported by adjustable

counter balance springs and adjustable gauge wheels. Gauge wheels are steel

construction with non–scuffing rubber tires and sealed ball bearings; infinitely

adjustable vertically.

Flex Tip Reel Drive

Banded double drive belt from engine pulley to jackshaft pulley; belt from jack shaft

(driver) pulley to flex tip reel (driven) pulley. Flex tip runs at 275 R.P.M. (tip speed

1355 ft./min.) at 3250 engine R.P.M.

Dimensions and Weights

(approx.)

Width

85–1/2”

Height

79–1/2”

Length

13’ 3”

Empty Weight

2160 lb. (Model 07050)

Optional Equipment

Hard Surface Brush Kit

Model No. 07162

Thatching Reel Kit

Model No. 07178

Flex Tip Reel

Model No. 07164

Spark Arrester Muffler

*

Kohler No 1218902

*

Contact Your Local Kohler Dealer

Содержание RAKE-O-VAC 07050

























Отзывы: