background image

11

Use 

unleaded

 regular gasoline suitable for automotive use

(85 pump octane minimum). Leaded regular gasoline may

be used if unleaded regular is not available.

Important

 

Never use methanol, gasoline containing

methanol, or gasohol containing more than 10% ethanol

because the fuel system could be damaged. Do not mix oil

with gasoline.

1.

Clean area around fuel tank cap.

2.

Remove fuel tank cap.

3.

Fill tank to about one inch below top of tank, (bottom of

filler neck). 

DO NOT OVERFILL.

 Then install cap.

4.

Wipe up any fuel that may have spilled to prevent a fire

hazard.

Check Tire Pressure

Check tire pressure daily to assure proper level.

Correct tire pressure is 28 psi.

Transport Hooks

1.

Lift each end of reel and remove transport hooks before

operating machine.

1

Figure 5

1. Transport hook

2.

When transporting sweeper from one location to

another, support flex tip reel, broom or thatching reel.

with transport hooks.

Adjust Reel Support Arm

When machine is operated, gauge wheel should ride over

the turf evenly. If reel support arm has a tendency to

bounce, spring setting is too tight. If gauge wheel scars turf,

spring setting is too light.

To adjust reel support arm:

1.

Pull rake lever rearward to lower flex tip reel or broom.

1

2

3

Figure 6

1. Spring scale
2. Counterbalance spring

3. Adjustment screw

2.

Position a spring scale on transport hook and lift up.

Tension necessary to lift gauge wheel off ground should

be 30–50 lbs.

3.

If tension is not 30–50 lbs., adjustment is made by

tightening or loosening adjustment screw on

counterbalance spring.

4.

Perform this procedure on both sides of sweeper.

Note:

 Because of added weight of drive components, the

R.H. spring will require a tighter setting than the L.H.

spring.

Содержание RAKE-O-VAC 07050

























Отзывы: