Toro ProLine 30441 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 64

Toro ProLine 30441 Скачать руководство пользователя страница 20

20

m-6505

3

2

1

Figure 12

1.

Hairpin cotter

2.

Unused spacers

3.

Height–of–cut post (front
shown)

Step

7

Checking the Tire Pressure

Parts needed for this step:

None

Procedure

Refer to page 39 for the correct correct tire pressure.

Step

8

Activating the Battery

Parts needed for this step:

Qty.

Part

80

ounces

Bulk electrolyte with 1.265 specific gravity
(Purchase from a battery supply outlet.)

Procedure

Bulk electrolyte with 1.265 specific gravity must be
purchased from a local battery supply outlet.

CALIFORNIA

Proposition 65 Warning

Battery posts, terminals, and related accessories
contain lead and lead compounds, chemicals
known to the State of California to cause cancer
and reproductive harm. Wash hands after
handling.

Warning

Danger

Battery electrolyte contains sulfuric acid which is
a deadly poison and causes severe burns.

•

Do not drink electrolyte and avoid contact with
skin, eyes or clothing. Wear safety glasses to
shield your eyes and robber gloves to protect
your hands.

•

Fill the battery where clean water is always
available for flushing the skin.

•

Follow all instructions and comply with all
safety messages on the electrolyte container.

1. Remove the battery from the machine. Refer to

Removing the Battery on page 36.

«
...
18
19
20
21
22
...
»

Содержание ProLine 30441

































































Отзывы:

Нет отзывов