background image

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area of potential
danger. Replace any decal that is damaged or lost.

115-5105

1.

Warning—read the

Operator's Manual.

2.

Warning—do not operate this machine unless you are trained.

3.

Warning—stop the engine; remove the ignition key and read the instructions before servicing or performing maintenance.

4.

Thrown object hazard—keep bystanders a safe distance from the machine.

5.

Warning—stay away from moving parts; keep all guards in place.

6.

Warning—do not start the engine when machine is disconnected from the tow vehicle, hitch the machine to the tow vehicle
before starting the engine.

115-5106

1.

Warning—read the

Operator's Manual.

2.

Thrown object hazard—keep bystanders a safe distance
from the machine.

3.

Cutting/dismemberment hazard; hand—stay away from
moving parts; keep all guards and shields in place.

115-5113

1.

Warning—read the

Operator's Manual,

wear hearing and

eye protection.

119–6165

1.

Engine—Stop

3.

Engine—Start

2.

Engine—Run

7

Содержание ProForce 44539

































Отзывы: