Toro groundsmaster 3240-d Скачать руководство пользователя страница 70

Страница: 70 / 81

1.70

ELECTRICAL CIRCUIT DIAGRAM

Switch - Parking Brake Interlock.

950865

Glow Plug Timer.

15694-65992

Light - Parking Brake.

924601/950858

Light - Glow Plugs.

924601/950857

Light - Neutral.

924601/950862

Light - Cutterdeck Drive Off.

924601/950861

Light - Return Filter.

924601/950866

Light - Pressure Filter.

924601/950863

Light - Battery Warning.

924601/924605

10.

Light - Engine Oil Pressure.

924601/924606

11.

Light - Engine Coolant Temperature.

924601/924602

12.

Light - Hydraulic Oil Temperature.

924601/924603

13.

Diodes - Overheat - Audible Warning.

950868

Supplied with Loom

14.

Switch - Beacon (supplied with beacon kit).

924608

15.

Switch - Work/Transport Mode.

924607

16.

Solenoid - L/H Cutterdeck Drive.

70-06-246

17.

Solenoid - Centre Cutterdeck Drive.

70-06-246

18.

Solenoid - R/H Cutterdeck Drive.

70-06-246

19.

Switch - R/H Deck Interlock.

20.

Switch - Cutterdeck Drive 511.106.

924607

(Lens 950856)

21.

Fusebox.

70-09-096

1. 10A Cutter Drive & Lift Configuration

70-09-026

2. 10A Transmission & Horn

70-09-026

3. 3A Instruments

70-09-024

4. Blank (Beacon)

5. Blank (Cab Wipers) or (Air Suspension Seat)

6. Blank (Lighting Kit)

7. Blank (Lighting Kit)

8. 30A Engine Start (Fuel Solenoid)

70-09-027

22.

Switch - Ignition.

74-09-009

23.

Switch - Horn.

924618

24.

Fuse - Engine Glow Plugs 60A.

Supplied with Loom

25.

Relay - Overheat Audible Warning.

70-09-148

Supplied with Loom

26.

Diode - Seat Switch.

950868

Supplied with Loom

27.

Relay - Glow Plugs.

924625

Supplied with Loom

28.

Timer - Operator Presence Interlock.

70-01-512

29.

Diode - Parking Brake.

950868

Supplied with Loom

30.

Relay - Seat Switch.

70-09-148

Supplied with Loom

31.

Temperature Gauge (supplied with temp kit).

32.

33.

Connectors for Lighting Kit.

Supplied with Loom

34.

Horn.

70-09-108

35.

Switch - Operator Seat.

953819

36.

Solenoid - Differential Lock.

910627

37.

Switch - Differential Lock.

924624

38.

Switch - Pressure Filter.

39.

Switch - Hydraulic Oil Temperature.

940852

40.

Connection for Beacon Kit.

Supplied with Loom

41.

Switch - Neutral/Starter Interlock.

955711

42.

Battery.

70-09-015

43.

Switch - Engine Oil Pressure.

44.

Starter Motor.

ITEM NO.

DESCRIPTION

PART NO.

Содержание groundsmaster 3240-d


















































































Результаты поиска

Содержание groundsmaster 3240-d

Отзывы:

Похожие инструкции для groundsmaster 3240-d

Бренды по названию

Популярные бренды

Toro groundsmaster 3240-d, Руководство оператора

Результаты поиска

Содержание groundsmaster 3240-d

Отзывы:

Похожие инструкции для groundsmaster 3240-d

Бренды по названию

Популярные бренды