Toro groundsmaster 3240-d Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 81

background image

1.35

1.35

OPERATING THE MOWER

TRANSMISSION NEUTRAL INDICATOR LIGHT

Illuminates when the travel control pedal is in the
neutral position and the ignition key is turned to position ‘I’.

Note:

The parking brake must be engaged for the transmission neutral indicator light

to illuminate.

CUTTERDECK DRIVE SWITCH INDICATOR LIGHT

Illuminates when the cutterdeck drive switch is in the ‘off’ position and the ignition
key is turned to position ‘I’.

PARKING BRAKE INDICATOR LIGHT

Illuminates when the parking brake is engaged and the ignition key is turned to posi-
tion ’I’.

HYDRAULIC RETURN FILTER INDICATOR LIGHT

Illuminates when the return filter element is blocked.

Note: The engine must be running for the hydraulic return filter indicator light
to illuminate. The indicator light may illuminate briefly when the hydraulic oil
is cold.

HYDRAULIC TRANSMISSION FILTER INDICATOR LIGHT

Illuminates when the transmission filter element is blocked.

Note: The engine must be running for the hydraulic return filter indicator light
to illuminate. The indicator light may illuminate when the hydraulic oil is cold.

Illuminates when the transmission system ‘work’ mode is selected and the ignition
key turned to position ‘I’

N

WS041

KG001

WS045

P

WS043

WS042

TRANSMISSION SYSTEM ‘WORK’ MODE INDICATOR LIGHT

WS055

KG001

KG002

Disngaged

Cutterblade

Engaged
Cutterblade

«
...
33
34
35
36
37
...
»

Содержание groundsmaster 3240-d


















































































Отзывы:

Нет отзывов

Похожие инструкции для groundsmaster 3240-d

Бренд: Sabre Страницы: 9

Бренд: Cadet Страницы: 40

Бренд: Lastec Страницы: 69

Бренд: Snapper Страницы: 25

Бренд: Gardena Страницы: 52

Бренд: Jacobsen Страницы: 62

Бренд: Yard-Man Страницы: 16

Бренд: MTD Страницы: 12

TZ51SF-BS625EXi

Бренд: MADER Страницы: 67

Бренд: Toro Страницы: 52

Бренд: FGM Страницы: 33

Бренд: Snapper Страницы: 52

Stockman 4000 A16314E

Бренд: COX Страницы: 50

Бренд: LawnMaster Страницы: 16

Бренд: Land Pride Страницы: 2

Бренд: ARNETOLI MOTOR Страницы: 2

Бренд: Kubota Страницы: 24

Бренд: Poulan Pro Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды