Toro groundsmaster 3240-d Скачать руководство пользователя страница 22

Страница: 22 / 81

1.22

SPECIFICATIONS

Automotive padded steering wheel with adjustable steering
column.

Electrical switch (on - off).

Hand operated lever.

Separate foot operated pedals.

Key start, shut - off and engine preheat.

Foot pedal.

Electrical Switch.

Hand operated lever.

Button switch.

Engine oil pressure.
Battery charge.
Engine coolant temperature.
Hydraulic transmission oil temperature.

Digital hour meter.
Fuel level.
Hydraulic oil level sight glass.

Engine pre-heat.
Hydraulic return filter blocked.
Hydraulic transmission filter blocked.
Cutterdeck drive switch off.
Parking brake engaged.
Transmission neutral.
‘Work’ mode active.

Steering:

Cutter Drive:

Engine Speed:

Parking Brake:

Forward and Reverse:

Ignition:

Differential Lock:

‘Work’ or ‘Transport’ modes:

Cutterdeck Position:

Horn:

OPERATOR CONTROLS

INSTRUMENTATION

Warning Lights:

Gauges:

Indicator Lights:

Содержание groundsmaster 3240-d


















































































Результаты поиска

Содержание groundsmaster 3240-d

Отзывы:

Бренды по названию

Популярные бренды

Toro groundsmaster 3240-d, Руководство оператора

Результаты поиска

Содержание groundsmaster 3240-d

Отзывы:

Бренды по названию

Популярные бренды