Toro Greensmaster Flex 2120 Скачать руководство пользователя

Страница: 19 / 44

Setting the Machine to Match Turf Conditions

Use the following table to set the machine to match turf conditions.

Bedbars: Standard and Optional (Flex/eFlex 2120 Machines)

Part Number

Description

Aggressiveness

Comments

106-2468-01

Non-Aggressive

Less

Red, Standard

99-3794-03

Aggressive

Black

Bedbars: Standard and Optional (Flex/eFlex 1820 Machines)

110-2282-01

Non-Aggressive

Less

Red, Standard

110-2281-03

Aggressive

Black

Bedknives: Standard and Optional (Flex/eFlex 2120 Machines)

Part Number

Description

Height-of-cut Range

Comments

115-1880

Microcut-EdgeMax

1.6 to 3.2 mm (0.062 to 0.125 inch)

Standard

93-4262

Microcut

1.6 to 3.2 mm (0.062 to 0.125 inch)

108-4303

Extended Microcut

1.6 to 3.2 mm (0.062 to 0.125 inch)

Less aggressive

115-1881

Tournament- EdgeMax

3.2 to 6.4 mm (0.125 to 0.25 inch)

93-4263

Tournament

3.2 to 6.4 mm (0.125 to 0.25 inch)

108-4302

Extended Tournament

3.2 to 6.4 mm (0.125 to 0.25 inch)

Less aggressive

93-4264

Low Cut

6.4 mm (0.25 inch) and up

Bedknives: Standard and Optional (Flex/eFlex 1820 Machines)

117-1530

Microcut-EdgeMax

1.6 to 3.2 mm (0.062 to 0.125 inch)

Standard

98-7261

Microcut

1.6 to 3.2 mm (0.062 to 0.125 inch)

110-2300

Extended Microcut

1.6 to 3.2 mm (0.062 to 0.125 inch)

Less aggressive

98-7260

Tournament

3.2 to 6.4 mm (0.125 to 0.25 inch)

117-1532

Tournament- EdgeMax

3.2 to 6.4 mm (0.125 to 0.25 inch)

110-2301

Low Cut

6.4 mm (0.25 inch) and up

Rollers (Flex/eFlex 2120 Machines)

Part Number

Description

Diameter/Material

Comments

04255

Narrow Wiehle

6.4 cm (2.5 inches)/Aluminum

Narrow spaced grooves

04256

Wide Wiehle

6.4 cm (2.5 inches)/Aluminum

More penetration, wide spaced grooves

04257

Full Roller

6.4 cm (2.5 inches)/Steel

Least penetration

04258

Narrow Wiehle—Long

6.4 cm (2.5 inches)/Aluminum

More edge support; 4.3 cm (1.7 inches) longer

04267

Paspalum

6.4 cm (2.5 inches)/Aluminum

Less penetration, softened narrow spaced grooves

115-7356

Rear Roller

5.1 cm (2.0 inches)/Aluminum

Standard rear

120-9595

Rear Roller

5.1 cm (2.0 inches)/Steel

Steel rear

Rollers (Flex/eFlex 1820 Machines)

120-9607

Narrow Wiehle

6.4 cm (2.5 inches)/Aluminum

Narrow spaced grooves

120-9609

Wide Wiehle

6.4 cm (2.5 inches)/Aluminum

More penetration, wide spaced grooves

120-9611

Full Roller

6.4 cm (2.5 inches)/Steel

Least penetration

121-4681

Narrow Wiehle—Long

6.4 cm (2.5 inches)/Aluminum

More edge support; 4.3 cm (1.7 inches) longer

120-9605

Rear Roller

5.1 cm (2.0 inches)/Aluminum

Standard rear

Содержание Greensmaster Flex 2120













































Результаты поиска

Содержание Greensmaster Flex 2120

Отзывы:

Похожие инструкции для Greensmaster Flex 2120

Бренды по названию

Популярные бренды

Toro Greensmaster Flex 2120, Руководство оператора

Результаты поиска

Содержание Greensmaster Flex 2120

Отзывы:

Похожие инструкции для Greensmaster Flex 2120

Бренды по названию

Популярные бренды