Toro 79485 Скачать руководство пользователя страница 1

Form No. 3453-656 Rev A

ROPS Kit

TimeCutter

®

Riding Mower

Model No. 79485—Serial No. 400000000 and Up

Installation Instructions

Store this document with the

Operator’s Manual

for the traction unit.

Safety

Rollover Protection System
(ROPS) Safety

The ROPS is an integral safety device. Do not
remove any of the ROPS components from the
machine.

Ensure that the seat belt is attached and that you
can release it quickly in an emergency.

Always wear your seat belt when the roll bar is
installed.

Check carefully for overhead objects before you
drive under them, and do not contact them.

Keep the roll bar in safe operating condition by
thoroughly inspecting it periodically for damage
and keeping all the mounting fasteners tight.

Replace damaged ROPS components. Do not
repair or alter them.

Wheels dropping over edges, over steep banks, or
into water can cause a rollover, which may result
in serious injury or death.

Do not wear the seat belt when the roll bar is not
installed.

In the event of a rollover, take the machine to an
Authorized Service Dealer to inspect the ROPS.

Use only Toro approved accessories and
attachments for the ROPS.

Safety and Instructional
Decals

Safety decals and instructions are
easily visible to the operator and are
located near any area of potential
danger. Replace any decal that is
damaged or missing.

decal145-6387

145-6387

1.

Warning—Read the

Operator's Manual

and wear a seat

belt.

© 2022—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

Register at www.Toro.com.

Original Instructions (EN)

Printed in the USA

All Rights Reserved

*3453-656*

 

Содержание 79485

















Отзывы: