Toro 78281 Скачать руководство пользователя страница 19

Страница: 19 / 20

Troubleshooting

Problem

Possible Causes

Corrective Action

Abnormal vibration.

Cutting blade(s) is bent or
unbalanced.

Install new cutting blade(s).

Blade mounting bolt is loose.

Tighten blade mounting bolt.

Engine mounting bolts are
loose.

Tighten engine mounting
bolts.

Loose engine pulley, idler
pulley, or blade pulley.

Tighten the appropriate
pulley.

Engine pulley is damaged.

Contact Authorized Service
Dealer.

Blade(s) does not rotate.

Blade drive belt is worn, loose
or broken.

Install new blade drive belt.

Blade drive belt is off pulley.

Install blade drive belt and
check idler pulley and belt
guides for correct position.

PTO belt is worn, loose or
broken.

Install new PTO belt.

Uneven cutting height.

Tire pressure is incorrect.

Set tire pressure.

Mower is not level.

Level mower from
side-to-side and front-to-rear.

Underside of mower is dirty.

Clean the underside of the
mower.

Содержание 78281





















Результаты поиска

Содержание 78281

Отзывы:

Похожие инструкции для 78281

Бренды по названию

Популярные бренды

Toro 78281, Руководство оператора

Результаты поиска

Содержание 78281

Отзывы:

Похожие инструкции для 78281

Бренды по названию

Популярные бренды