background image

Operation

CAUTION

Chemicals are hazardous and can cause personal
injury.

Read the directions on the chemical labels
before handling the chemicals and follow
all manufacturer recommendations and
precautions.

Keep chemicals away from your skin. Should
contact occur, wash the affected area thoroughly
with soap and clean water.

Wear goggles and any other protective
equipment recommended by the chemical
manufacturer.

Controls

Figure 24

1.

Lid

6.

Tank hose

2.

Supply hose

7.

T-valve

3.

Main valve

8.

Upper handle

4.

Transport strap

9.

Flush valve

5.

Lower handle

Lid

Rotate the lid counter clockwise to open it. Close the lid
completely before turning it clockwise to lock it. You must
close the lid and lock it before it is raised to the Transport
position.

Handles and Transport Strap

Use the upper and lower handles to raise and lower the
eductor and to lock it into the Transport position.

Main Valve

Use the main valve to introduce chemicals from the eductor
into the hose leading to the main tank.

Bottle Rinse

The bottle rinse is located inside the eductor tank. Once
the eductor switch is on, the bottle rinse has pressure and is
supplied by the contents of the main tank. To use the bottle
rinse, invert the chemical container over the spout and use
the rim of the container to depress the rinse. Press down
to actuate the spout and rinse the interior of the chemical
container.

Figure 25

1.

Bottle rinse

Flush Valve

The flush valve can rinse the inside of the eductor tank. Once
the eductor switch is on, the flush valve will have pressure
and is supplied by the contents of the main tank. To open
the valve, turn the handle 90° counterclockwise. This will in
introduce water to the tank. Turn the handle 90° clockwise
to close the valve.

Raising and Lowering the
Eductor

Lowering the Eductor

1.

Unlatch the rubber transport strap.

2.

Place a hand on the lower handle and the other hand
on the upper handle.

3.

Lift the eductor away from the vehicle until the spring
clamp disengages.

4.

Guide the eductor as it lowers to the operating position.

14

 

Содержание 41622





















Отзывы: