Toro 30230 Groundsmaster 225, Руководство оператора

Страница: 13 / 32

+)52'
#&+#402 %#1
81#/3+0/ 4#/, %#1
81#/3+0/ 4#/, (+-- .#2,3
Check level of coolant in radiator. Radiator should
be filled to the top of the filler neck and the expansion
tank filled to between the marks on its side.
If coolant level is low, replenish the system. DO
NOT OVERFILL.
Install radiator cap and expansion tank cap.
" "
The hydraulic system was designed to operate on any
high quality detergent oil having the American
Petroleum InstituteĊAPIĊservice classification" SF,
CC or CD. Oil viscosity Ċ weight Ċ must be selected
according to anticipated ambient temperature.
Temperature/viscosity recommendations are:
81'%4'& '%0..'/&'&
.$+'/4 +3%03+49
'.1'2#452' #/& 91'
(Extreme) over 90 F SAE 30, Type SF, CC or CD
engine oil.
(Normal) 40Ć100 F SAE 10WĆ30 or 10WĆ40.
Type SF, CC or CD engine oil.
(CoolĊSpring/Fall) SAE 5WĆ30, Type SF, CC or
30-50 F CD engine oil.
(Winter) Below 30 F Type F" or FA" ATF Automatic
Transmission Fluid.
04' Do not mix engine oil and automatic
transmission fluid or hydraulic component damage
may result. When changing fluids, also change
transmission filter. !
The axle housing acts as the reservoir for the system.
The transmission and axle housing are shipped from
the factory with approximately 5 quarts (4.7 l) of SAE
10WĆ30 engine oil. However, check level of
transmission oil before engine is first started and daily
thereafter.
Position machine on a level surface. Place all
control in neutral position and start the engine. Run
engine at lowest possible RPM to purge the system of
air. Cycle steering wheel
several times fully to the left and right. Raise the cutting
unit to extend lift cylinders, aiming steering wheels
straight forward and stop the engine.
Remove dipstick cap (Fig. 14) from filler neck and
wipe it with a clean rag. Screw dipstick cap fingerĆtight
onto filler neck; then remove it and check level of fluid. If
level is not within 1/2 inch (13 mm) from the groove in
the dipstick (Fig. 14), add SAE 10WĆ30 engine oil, or, if
used, automatic transmission fluid to raise level to
groove mark. Do not overfill.
+)52'
9&2#5-+% 3934'. 2'3'260+2 (-5+&#&& &+134+%, %#1
*'/ #&&+/) 42#/3.+33+0/ (-5+& 40 4*'
*9&2#5-+% 3934'. 53' # (5//'- 7+4* # (+/' 7+2'
3%2''/ : .'3* 02 (+/'2 : #/& .#,' 352' (5//'-
#/& 42#/3.+33+0/ (-5+& #2' +..#%5-#4'-9 %-'#/ *+3
120%'&52' 12'6'/43 #%%+&'/4#- %0/4#.+/#4+0/ 0(
4*' *9&2#5-+% 3934'.
Thread dipstick fill cap fingerĆtight onto filler neck.
It is not necessary to tighten cap with a wrench.
Check all hoses and fittings for leaks.
" "
!
"
NEVER USE METHANOL, GASOLINE
CONTAINING METHANOL, GASOLINE CONTAINING
MORE THAN 10% ETHANOL, GASOLINE ADDITIVES,
PREMIUM GASOLINE OR WHITE GAS BECAUSE
ENGINE FUEL SYSTEM DAMAGE COULD RESULT.
Clean area around fuel tank cap (Fig. 15).
Remove fuel tank cap.