4
•
Logs should be cut with ends as square as possible prior to
splitting.
•
Block the machine to prevent unintended movement, and
lock in either horizontal or vertical position.
•
Use extra care when handling gasoline and other fuels. They
are flammable and vapors are explosive.
•
Use only an approved fuel container.
•
Never remove the gas cap or add fuel when the engine is
running. Allow the engine to cool before refueling. Do
not smoke.
•
Never refuel or drain the machine indoors.
•
Replace gasoline cap and tighten securely.
•
Keep container nozzle in contact with the tank during
filling.
•
If gasoline is spilled, wipe it off the engine and
equipment.
Operation
Before every use:
•
Inspect the coupler, ball and hitch.
•
Always use safety chains.
•
Verify all lights are functioning properly.
•
Verify the tires are properly inflated as recommended on
tires.
•
Verify lug nuts are tight and torqued properly.
•
Machine is properly secured.
•
Before starting this machine, review the “Safety
Instructions” Failure to follow these rules may result in
serious injury to the operator or bystanders.
•
Never leave this machine unattended with the engine
running.
•
Never operate machine while under the influence of alcohol,
drugs, or medication.
•
Never allow anyone to operate this machine without proper
instruction.
•
Always operate this machine with all safety equipment in
place and working.
•
Do not change the engine governor setting or over speed the
engine.
•
Use only your hand to operate the control lever.
Always keep hands and feet clear of moving parts.
•
Never place your hands or feet between the log and the
splitting wedge or between the log and the ram during the
forward or reverse stroke.
•
When loading a log, place your hands on the sides of the
log, not on the ends. Never place your hands or any part of
your body between a log and any part of the log splitter.
•
Do not straddle or reach across the log splitting area when
operating the machine.
•
Never attempt to split more than one log at a time.
•
For logs which are not cut square, the least-square end and
the longest portion of the log should be placed toward the
beam and wedge, and the square end placed toward the end
plate.
•
Keep the work area clean; remove split logs from around the
machine so you do not slip on them.
•
Do not touch parts which may be hot from operation. Allow
them to cool before attempting to maintain, adjust, or service.
•
Locate the pinch point areas marked on the machine and
keep hands and feet away from these areas.
•
Never run an engine in an enclosed area.
•
Never move this machine while the engine is running.
•
Lightning can cause severe injury or death. If lightning is
seen or thunder is heard in the area, do not operate the
machine; seek shelter.
•
Do not touch the engine or muffler while the engine
is running or soon after it is stopped. These areas
could be hot enough to cause a burn.
Maintenance and Storage
•
Stop the engine and remove the spark plug wire before
making any repairs. Wait for all movement to stop before
adjusting, cleaning, or repairing.
•
Inspect the machine before each use. Make sure all nuts,
bolts, screws, hydraulic fittings, hose clamps, are securely
tightened.
•
Clean debris from the muffler and engine to help prevent
fires. Clean up oil or fuel spillage.
•
Let the engine cool before storing and do not store near
flame.
•
Do not store fuel near flames or drain indoors.
•
Park the machine on level ground. Never allow untrained
personnel to service the machine.
•
Keep hands and feet away from moving parts. If possible,
do not make adjustments with the engine running.
•
Keep all parts in good working condition and all hardware
tightened. Replace all worn or damaged decals.
•
Use extra care when handling gasoline and other fuels. They
are flammable and vapors are explosive.
•
Never store the machine or fuel container inside where there
is an open flame, such as near a water heater or furnace.
•
Use only genuine Toro replacement parts to ensure that
original equipment standards are maintained.
