Toro 133-0150 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 20

Toro 133-0150 Скачать руководство пользователя страница 8

g192299

Figure 13

1.

Adjusting bolt

4.

Capscrew

2.

Locknut

5.

Flange nut

3.

Carriage bolt and flange
locknut (3/8 with 5/8 inch
hex)

5.

Tighten the locknut on the HOC adjuster bolt,
then back off the locknut 1/2 turn (

6.

Center the front roller between the HOC bracket
assemblies and lock it in place with the cap
screws and flange nuts (

).

8

Installing the Groomer
Drive Cap

Parts needed for this procedure:

1

Cap

Procedure

Only for Universal Groomer assemblies with no
rear roller brush kit installed:

1.

Apply medium-strength cylindrical bonding
retaining compound (such as Green Loctite
609®) around the snap ring groove and the
outer diameter surface (

2.

Install the cap as shown in

g242099

Figure 14

1.

Cap

2.

Apply Green Loctite 609®

3.

If you are installing the groomer at the left side of
the machine, perform the following (

):

A.

Remove the O-ring from the clutch knob.

B.

Remove the shear pin that secures the
clutch knob to the actuator shaft.

C.

Remove the clutch-knob assembly and flip
it over.

D.

Assemble the clutch knob to the actuator
shaft with the shear pin.

E.

Install the O-ring into the groove in the
clutch knob.

g246113

Figure 15

Left-side install shown

1.

Shear pin

3.

O-ring

2.

Clutch-knob assembly

8

«
...
6
7
8
9
10
...
»

Содержание 133-0150





















Отзывы:

Нет отзывов