Toro 133-0150 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 20

Toro 133-0150 Скачать руководство пользователя страница 11

10

Installing the Angled Fitting

For Reelmaster 3550 and 3555
Machines—#1 Front, Center
Cutting Location and Kit Model
133-0150 Only

Parts needed for this procedure:

1

Hydraulic fitting—45° (Part No. 340–101; sold
separately)

Procedure

Important:

For Reelmaster 3550 and 3555

machines—#1 front, center cutting location and
kit model 133-0150 only; order 45° hydraulic fitting
(Part No. 340–101) and follow the procedure
below.

1.

Remove the hydraulic hose from the hydraulic
fitting on the motor.

2.

Remove the 2 O-rings on the new 45° fitting,
lubricate them with grease, and install them on
the fitting.

3.

Remove the existing fitting.

4.

Install the new 45° fitting, positioning the fitting
with the angle of the fitting as shown in

. Torque the fitting to 47 to 58 N∙m (35 to 43

ft-lb).

g190850

Figure 20

1.

Cutting unit motor

3.

Groomer adjuster

2.

45° fitting

5.

Connect the hydraulic hose into the new fitting;
torque the hose fitting to 40 to 64 N∙m (37 to 47
ft-lb).

Note:

Ensure that the fitting is positioned so

that the hose does not contact the groomer
adjuster.

11

«
...
9
10
11
12
13
...
»

Содержание 133-0150





















Отзывы:

Нет отзывов