Toro 133-0150 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 20

Toro 133-0150 Скачать руководство пользователя страница 6

6

Installing the Idler
Assembly

Parts needed for this procedure:

2

Hex-socket-head bolt

1

Pivot hub

1

O-ring

1

Idler assembly

2

Bearing shield

1

Adjuster collar

1

Stub-shaft assembly

1

Flange nut (3/4 inch)

2

Flange locknut (3/8 inch)—Model 133-0150 only

2

Jam locknut (3/8 inch)—Model 133-0151 only

Procedure

1.

Assemble the parts that make up the idler
assembly as shown in

. Torque the

flange nut (3/4 inch) to 37 to 45 N∙m (27 to 33
ft-lb); torque the adjuster collar to 33 to 41 N∙m
(24 to 30 ft-lb).

g035823

Figure 9

1.

Hex-socket-head bolt (2)

6.

Apply anti-seize
compound on the outside
diameter of the hub.

2.

Pivot hub

7.

Flange nut (3/4 inch)

3.

O-ring

8.

Bearing shield

4.

Idler assembly

9.

Adjuster collar

5.

Locknut—3/8 inch (2)

10.

Stub-shaft assembly

2.

Position the idler assembly on the opposite side
of the reel from the groomer drive box.

3.

Install the O-ring onto the pivot-hub assembly.

4.

Apply anti-seize compound on the outside
diameter of the pivot-hub assembly (

5.

Secure the pivot hub over the idler assembly to
the reel using 2 hex-socket bolts (

).

6.

Loosely install the 2 locknuts on the pivot hub
(

).

6

«
...
4
5
6
7
8
...
»

Содержание 133-0150





















Отзывы:

Нет отзывов