Toro 13-32H Wheel Horse Скачать руководство пользователя страница 34

Страница: 34 / 36

Problem

Corrective Action

Possible Causes

The engine overheats.

1. The engine load is excessive.

1. Reduce the ground speed.

2. The oil level in the crankcase is

low.

2. Add oil to the crankcase.

3. The cooling fins and air

passages under the engine
blower housing are plugged.

3. Remove the obstruction from

the cooling fins and air
passages.

There is an abnormal vibration.

1. The blade is bent or

unbalanced.

1. Install a new blade.

2. The blade mounting bolt is

loose.

2. Tighten the blade mounting

bolt.

3. The engine mounting bolts are

loose.

3. Tighten the engine mounting

bolts.

4. There is a loose engine pulley,

idler pulley, or blade pulley.

4. Tighten the appropriate pulley.

5. The engine pulley is damaged.

5. Contact an Authorized Service

Dealer.

The blade does not rotate.

1. The blade drive belt is worn,

loose, or broken.

1. Contact an Authorized Service

Dealer.

2. The blade drive belt is off of the

pulley.

2. Contact an Authorized Service

Dealer.

The machine does not drive.

1. The traction belt is worn, loose,

or broken.

1. Contact an Authorized Service

Dealer.

2. The traction belt is off the

pulley.

2. Contact an Authorized Service

Dealer.

3. The transmission does not

shift.

3. Contact an Authorized Service

Dealer.

The cutting height is uneven.

1. The tire pressure is incorrect.

1. Set the tire pressure.

2. The mower is not level.

2. Level the mower.

3. The underside of the mower is

dirty.

3. Clean under the mower.

The cutting quality is poor.

1. The cutting blade is worn.

1. Sharpen or replace the cutting

blade.

2. The cutting height is incorrect.

2. Adjust the cutting height.

The grass collector fails to fill.

1. The cutting height is too low.

1. Raise the cutting height.

2. The grass is too heavy or

damp.

2. Wait until the grass has dried.

3. The cutting blade is worn.

3. Sharpen or replace the blade.

4. The grass is too high.

4. Raise the cutting height.

5. The discharge area is blocked.

5. Remove the obstruction from

the discharge area.

Содержание 13-32H Wheel Horse





































Результаты поиска

Содержание 13-32H Wheel Horse

Отзывы:

Похожие инструкции для 13-32H Wheel Horse

Бренды по названию

Популярные бренды

Toro 13-32H Wheel Horse, Руководство оператора

Результаты поиска

Содержание 13-32H Wheel Horse

Отзывы:

Похожие инструкции для 13-32H Wheel Horse

Бренды по названию

Популярные бренды