"
Release latches securing air cleaner cover to air
cleaner body. Separate cover from body. Clean inside
of air cleaner cover.
Gently slide primary filter (Fig. 32) out of air cleaner
body to reduce the amount of dust dislodged. Avoid
knocking filter against air cleaner body.
0 /04
2(.06( 3%)(48 ),-4(2
Inspect primary filter and discard if damaged. Do
not wash or reuse a damaged filter.
(6(2 %44(.14 40 &-(%/ % 3%)(48 ),-4(2
0&%4(' ,/3,'( 12,.%28 ),-4(2 (1-%&( 4+( 3%)(48
),-4(2 7,4+ % /(7 0/( %)4(2 (6(28 4+2(( 12,.%28 ),-4(2
3(26,&(3
#%3+,/* (4+0'
A. Prepare a solution of filter cleaner and water
and soak filter element about 15 minutes. Refer to
directions on filter cleaner carton for complete
information.
B. After soaking filter for 15 minutes, rinse it with
clear water. Maximum water pressure must not
exceed 40 psi to prevent damage to the filter
element. Rinse filter from clean side to dirty to side.
C. Dry filter element using warm, flowing air
(160
_
F ) max), or allow element to air-dry. Do not
use a light bulb to dry the filter element because
damage could result.
0.12(33(' ,2 (4+0'
A. Blow compressed air from inside to the outside
of dry filter element. Do not exceed 100 psi to
prevent damage to the element.
B. Keep air hose nozzle at least 2" from filter and
move nozzle up and down while rotating the filter
element. Inspect for holes and tears by looking
through the filter toward a bright light.
Inspect new filter for shipping damage. Check
sealing end of filter. Do not install a damaged filter.
Insert new filter properly into air cleaner body.
Make sure filter is sealed properly by applying pressure
to outer rim of filter when installing. Do not press on
flexible center of filter.
Reinstall cover and secure latches.
Reset indicator (Fig. 32) if showing red.
,*
Change oil and filter initially after the first 50 hours of
operation, thereafter, change oil and filter every 100
hours.
Raise bed (if so equipped) and place a safety
support under it to hold up bed.
Remove drain plug and let oil flow into drain pan.
When oil stops, install drain plug.
,*52(
/*,/( ,- 2%,/ -5*
Remove oil filter. Apply a light coat of clean oil to the
new filter seal before screwing it on. Screw filter on until
gasket contacts mounting plate, then tighten 1/2 to 2/3
of a turn. DO NOT OVER-TIGHTEN.
,*52(
/*,/( ,- ,-4(2
Add oil to crankcase, refer to Check Engine Oil.
! $
,*
5(- ,/(3 %/' 0//(&4,0/3
Check lines and connections every 400 hours or yearly,
whichever comes first. Inspect for deterioration,
damage, or loose connections.
5(- ,-4(2#%4(2 (1%2%402
Drain water or other contaminants from fuel filter/water
separator daily by loosening drain plug (Fig. 36) on
filter canister. Tighten plug after draining. Replace filter
canister after every 400 hours of operation.
Raise bed (if so equipped) and place a safety
support under it to hold up bed.
Содержание 07230
Страница 8: ...4 1 25 1203 2 1 0 12 2 5 0 0 2 02 3 01 0 12 4 2 021 2 0 0 0 21 0 5 30 32 0 6 120 32 0 02 02 02 02...
Страница 9: ......
Страница 10: ......
Страница 42: ......