Tornatech GLU Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 61

Tornatech GLU Скачать руководство пользователя страница 30

30

Most common timers for the transfer switch control can be configured here. Note that any timer set to 0 will remove
the delay in the decision process.

Access level 1:

- Cooling Time: Time delay after which a running generator can be shut down when all running causes have return
to normal.
- Retransfer time: Time delay used to re-qualify the normal power and retransfer. Typically five minutes.

Voltage Calibration

Config > Advanced > Voltage

To calibrate the voltage sensing element of a power source, enter the 3 phase voltages as read on a calibrated
meter then press compute. In the case of a transfer switch model, 3 additional voltages need to be calibrated the
same way.

Current Calibration

Config > Advanced > Current

To calibrate a particular current sensing element, enter the current value as read from a calibrated ammeter and
then press COMPUTE. For best results, press the ZERO button when no current is flowing through the sensing
element before calibrating.

«
...
28
29
30
31
32
...
»

Содержание GLU






























































Отзывы:

Нет отзывов