Tormach Autofeed Bandsaw AF50 Скачать руководство пользователя страница 63

Страница: 63 / 90

11: TROUBLESHOOTING

©Tormach® 2020
Specifications subject to change without notice.

Page 63

UM10538: Tormach AF50 Autofeed Bandsaw (Version 0320A)

For the most recent version, see tormach.com/support

Error

Description

E12

Saw lift proximity sensors (up and down) are both active.

E13

Infeed and outfeed proximity sensors (forward and rear) are both active.

E15

The infeed table retract stroke timed out (on the initial stroke).

E16

The infeed table advance stroke timed out.

E17

The infeed table retract stroke timed out (on a subsequent stroke).

While troubleshooting error codes, examine the Stroke LEDs on the control panel, which correspond to the proximity sensors on the

bandsaw. If the LED light is illuminated, the proximity sensor is active.

×1

LED: Infeed (advance) proximity sensor

×2

LED: Outfeed (retract) proximity sensor

×4

LED: Saw up proximity sensor

×5

LED: Saw down proximity sensor

Содержание Autofeed Bandsaw AF50



























































































Результаты поиска

Содержание Autofeed Bandsaw AF50

Отзывы:

Похожие инструкции для Autofeed Bandsaw AF50

Бренды по названию

Популярные бренды

Tormach Autofeed Bandsaw AF50, Руководство оператора

Результаты поиска

Содержание Autofeed Bandsaw AF50

Отзывы:

Похожие инструкции для Autofeed Bandsaw AF50

Бренды по названию

Популярные бренды