Torc HYFLOW 230-2 Скачать руководство пользователя

Страница: 72 / 93

Checks and repairs on hydraulic components

Checking the low-pressure cut off valve

WARNING

Slipping hazard from leaked oil.
Bruising and bone fractures possible.



Clean up any leaked oil with a cloth or suitable binding

agents.



Wear safety shoes with non-slip soles.

CAUTION

Health hazard from contact with hydraulic oil.



Wear nitrile gloves and chemical-resistant protective

goggles during work that may include contact with

hydraulic oil.

To check the low-pressure cut off valve, proceed as follows:



Move the unit into the repair position for the upper structures, see from

page 51.



Remove the carrying handle, see from page 50.



Mount the protective caps and protective plugs of the couplings, see from

page 49.



Release the screw connections (A) on the cover with two combination

wrenches WAF 10, as described in the chapter “Moving the unit into the

repair position for t

he lower structures”, see from page

52.

Содержание HYFLOW 230-2






























































































Результаты поиска

Содержание HYFLOW 230-2

Отзывы:

Похожие инструкции для HYFLOW 230-2

Бренды по названию

Популярные бренды

Torc HYFLOW 230-2, Инструкции по техническому обслуживанию и ремонту

Результаты поиска

Содержание HYFLOW 230-2

Отзывы:

Похожие инструкции для HYFLOW 230-2

Бренды по названию

Популярные бренды