Torc HYFLOW 230-2 Скачать руководство пользователя

Страница: 52 / 93

Checks and repairs on hydraulic components

Moving the unit into the repair position for the lower structures

WARNING

Slipping hazard from leaked oil.
Bruising and bone fractures possible.



Clean up any leaked oil with a cloth or suitable binding

agents.



Wear safety shoes with non-slip soles.

CAUTION

Health hazard from contact with hydraulic oil.



Wear nitrile gloves and chemical-resistant protective

goggles during work that may include contact with

hydraulic oil.

Proceed as follows to bring the unit into the repair position for the lower

structures:



Place the unit on a solid surface.



Remove the carrying handle, see from page 50.



Release the screw connections (A) with two combination wrenches WAF 10.

Содержание HYFLOW 230-2






























































































Результаты поиска

Содержание HYFLOW 230-2

Отзывы:

Похожие инструкции для HYFLOW 230-2

Бренды по названию

Популярные бренды

Torc HYFLOW 230-2, Инструкции по техническому обслуживанию и ремонту

Результаты поиска

Содержание HYFLOW 230-2

Отзывы:

Похожие инструкции для HYFLOW 230-2

Бренды по названию

Популярные бренды